CISCO 6509 upgrade IOS Master/Slave Control Board

CISCO 6509 upgrade IOS Master/Slave Control Board
1: configure the TFTP server to find the updated IOS path. 6509 # copy tftp sup-bootflash: (migrate to IOS to sup-bootflash of the main engine) Address or name of remote host []? 10.1.1.2Source filename []? S3223-ipbasek9-mz.122-18.SXF6.bin (IOS name for logging in) Destination filename [s3223-ipbasek9-mz.122-18.SXF6.bin]? Accessing t ftp://10.1.1.2/s3223-ipbasek9-mz.122-18.SXF6.bin...Loading S3223-ipbasek9-mz.122-18.SXF6.bin from 10.1.1.2 (via FastEthernet1/1) :!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! [OK-27966916 bytes] 27966916 bytes copied in 222.684 secs (125590 bytes/sec) Verifying compressed IOS image checksum... verified compressed IOS image checksum for sup-bootflash:/s3223-ipbasek9-mz.122-18.SXF6.bin6509 # copy tftp slavesup-bootflash :( into IOS to the standby engine sup-bootflash) Address or name of remote host []? 10.1.1.2Source filename []? S3223-ipbasek9-mz.122-18.SXF6.bin (IOS name for logging in) Destination filename [s3223-ipbasek9-mz.122-18.SXF6.bin]? Accessing t ftp://10.1.1.2/s3223-ipbasek9-mz.122-18.SXF6.bin...Loading S3223-ipbasek9-mz.122-18.SXF6.bin from 10.1.1.2 (via FastEthernet1/1) :!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! [OK-27966916 bytes] 27966916 bytes copied in 275.427 secs (101540 bytes/sec) Verifying compressed IOS image checksum... verified compressed IOS image checksum for slavesup-bootflash:/s3223-ipbasek9-mz.122-18.SXF6.bin2: Check whether IOS is imported to the flash of the master and slave engines 6509 # show bootvar 3: set IOS as the updated IOS6509 # conf tEnter configuration commands, one per line. end with CNTL/z.20.9 (config) # no boot system sup-bootflash: s3223-ipba Sek9-mz.122-18.SXF.bin6509 (config) # boot system sup-bootflash: s3223-ipbasek9-mz.122-18.SXF6.bin! -- Note that the command is configured on the main engine at this time, but after configuration, the backup engine also synchronizes 6509 (config) # ^ z3169 # copy run startDestination filename [startup-config]? Building configuration... * Oct 13 03:21:05. 331: % PFINIT-SP-5-CONFIG_SYNC: Sync 'ing the startup configuration to the standby Router. [OK] 4: Check whether the Master/Slave engine is synchronized after the IOS Startup File is set to 6509 # show bootvar 5: reset the backup engine, let its new IOS use 6509 # hw-module 6 reset (reset the 6-slot backup engine) Proceed with reset of standby supervisor? [Confirm] % reset issued for standby supervisor6: Check whether the backup engine has been reset after waiting for a reset. 6509 # show module7: use the command to switch to the reset standby engine 6509 # redundancy force-switchover 8: reset the primary engine on the standby engine, let its new IOS use 6509 # hw-module 5 reset (reset the 5-slot main engine) 9: Wait for the reset to check whether the backup engine has been reset 6509 # show module10: use commands to switch to the reset master engine 6509 # redundancy force-switchover if you delete the original IOS operation as follows: Router # del sup-bootflash: s72033-pk9sv-mz.122-17a.SX4.binDelete filename [s72033-pk9sv-mz.122-17 A. SX4.bin]? Delete sup-bootflash: s72033-pk9sv-mz.122-17a.SX4.bin? [Confirm] Router # squee sup-bootflash: (deleting All files is equivalent to the recycle bin) All deleted files will be removed. Continue? [Confirm] Squeeze operation may take a while. Continue? [Confirm] 124 \ u0008 \ u0008 \ u0008 \ u0008 \ Users \ u0008 \ u0008 \ u0008 \ u0008 \ u0008 \ Users \ u0008 \ u0008 \ u0008 \ u0008 \ u0008 \ u0008 \ u0008 \ u0008 \ u0008 \ u0008 \ u0008 \ u0008 \ u0008 \ u0008 \ u0008 \ u0008 \ u0008 \ u0008 \ u0008 \ sup-bootflash complete the IOS operation is as follows: router # copy sup-bootflash: tftp: Source filename []? Sup-bootflash: s72033-psv-mz.122-18.SXD3.binAddress or name of remote host []? 10.100.1.9Destination filename [s72033-psv-mz.122-18.SXD3.bin]? The 6500 Engine board consists of two parts: the Management Engine SE and the multi-layer switching Feature Card MSFC. Both SE and MSFC have built-in Flash file systems for file storage. The device name is bootflash:. You can also insert the Flash card of the PCMCIA Interface into the engine. The device name is slot0: And slot1: or CF -- CompactFlash card, the device name is disk0: And in the command above disk1: slaveslot0 :.................... the value of slot0: slavesup-bootflash :...... bootflash: slavebootflash :............. the bootflash: 6509 of MSFC on the backup engine is changed to SUP-BOOTFLASH after it is upgraded to IOS. In the past, msfc bootflash on the RP will be considered as the engine BOOTFLASH. However, 6509 cannot be started through ios on the bootflash of MSFC. You must use SUP-BOOTFLASH. Note This!