BIOS error message

Boot BIOS language

Post problems will appear after a variety of English phrases, short sentences contain very important information, read this information can solve some of their own small problems, but these English baffled a part of the friends, the following are some common BIOS interpretation, we can refer to.

1.CMOS Battery failed

English: CMOS battery fails.

Explanation: This indicates that the CMOS battery is almost out of power, just replace the new battery.

2.CMOS Check sum error-defaults loaded

English: The CMOS has found an error when performing all checks to load the system preset values.

Explanation: In general, this sentence is said that the battery is fast, you can change the battery to try, if the problem is still not resolved, then the CMOS RAM may be a problem, if not a year to the dealer to replace a motherboard, after a year to let the dealer back to the manufacturer repair it!

3.Press ESC to skip memory test

Chinese: A memory check is in progress and can be skipped by pressing the ESC key.

Explanation: This is because there is no set of skip memory in the CMOS 第二、三、四次 test, boot will perform four memory tests, of course you can also press the ESC key to end the memory check, but each time it is too troublesome, you can enter the COMs settings after the BIOS featurs setup, Set the quick Power on self test to Enabled, save and restart.

4.Keyboard error or no Keyboard present

English: Keyboard error or keyboard not connected.

Explanation: Check the keyboard for loose or damaged connections.

5.Hard Disk Install failure

English: Hard disk installation failed.

Explanation: This is because the power cord or data cable of the hard drive may not be connected or the hard drive jumper is improperly set. You can check if the hard drive is plugged in, and see if the jumper on the same cable has the same set of jumpers on the two hard drives, as long as the jumper settings for the two hard drives are different (one set to master and the other set to slave).

6.Secondary slave Hard Fail

English: Failed to detect slave disk

Explanation: May be improper CMOS settings, such as not from the disk but in the CMOS set to have the slave disk, then there will be an error, you can enter the COMs settings select the IDE HDD Auto detection for hard disk detection. It may also be the power cord of the hard drive, the data cable may not be connected, or the hard drive jumper is improperly set, the workaround refer to 5th.

7.Floppy disk (s) fail or floppy disk (s) fail (80) or floppy disk (s) fail (40)

Chinese: Unable to drive floppy drive.

Explanation: The system prompts to find the floppy drive, see the floppy drive power and data cable is loose or wrong, or the floppy drive to another machine to try, if these are not, then had to buy another, fortunately, the floppy drive is not expensive.

8.Hard disk (s) diagnosis fail

English: Error occurred while performing hard drive diagnostics.

Explanation: This problem generally means that the hard disk itself has failed, you can put the hard disk on another machine to try, if the problem is not resolved, only to repair it.

9.Memory Test fail

Chinese: Memory detection failed.

Explanation: Reseat the memory bar to see if it can be solved, the problem is generally because the memory is incompatible with each other, go to another bar!

10.Override Enable-defaults Loaded

Chinese: The current CMOS settings do not start the system and load the preset values in the BIOS to start the system.

Explanation: In general, the settings in the COMs error, as long as you enter the COMs settings select Load Setup defaults load the system's original set value and then reboot.

11.Press TAB to show POST screen

English: Press the TAB key to toggle the screen display.

Explanation: Some OEMs will replace the BIOS preset display screen with their own design display screen, and we can press TAB to switch between the BIOS preset splash screen and the manufacturer's custom screen.

12.Resuming from Disk,press TAB to show POST screen

English: Resume boot from hard drive, press TAB to display the post screen).

Explanation: This is because some of the motherboard's bios** suspend to disk (the hard drive hangs) the function, if we use suspend to disk's way to shut down, then we will display this prompt message the next time you turn on the computer.

13.Hareware Monitor found an error,enter POWER MANAGEMENT setup for details,press F1 to Continue,del to enter setup

Chinese: monitoring function found error, enter Power MANAGEMENT Setup to view details, press F1 key to continue the boot program, press Del to enter COMs settings.

Explanation: Some motherboards have hardware monitoring function, you can set the motherboard and CPU temperature monitoring, voltage regulator voltage output quasi-monitoring and monitoring the speed of each fan, when the above monitoring function in the boot to detect abnormal situation, then the above paragraph will appear, then you can enter the COMs settings select Power MANAGEMENT SETUP, on the right of the **fan monitor**, **thermal monitor** and **voltage monitor** to see which part of the exception was issued and then resolved.

This article from the "Breeze with You" blog, declined reprint!

BIOS error message