ONU MA5620 Configuration service shunt (voip,iptv,internet)

Nu Service Shunt configuration:

Configure the traffic template.

Because VoIP, IPTV, Internet access through the same port, it is necessary to set the 802.1p priority of each business. The general priority is ranked by Internet service, IPTV, VoIP from low to high. Set the traffic template index number here, respectively

For 7, 8, 9,802.1p priority is 0, 4, 6 respectively.

(config) #traffic table IP index 7 name Internet Cir 10240 Priority 0 Priority-policy local-setting

(config) #traffic table IP index 8 name IPTV CIR 10240 Priority 4 Priority-policy local-setting

(config) #traffic table IP index 9 name VoIP Cir 10240 Priority 6 Priority-policy local-setting

Create a VLAN.

Create VLAN 100–103, where VLAN 101 is the multicast VLAN.

(config) #vlan 100-103 Smart

It'll take several minutes, and console could be timeout, please use command

Idle-timeout to set time limit

is sure to add VLANs? (y/n) [N]:y

The total of the VLANs has been processed is 4

The total of the added VLANs is 4

Join the upstream port.

Add the upstream port 0/0/1 to the VLAN.

(config) #port vlan 100-103 0/0 1//onu device upstream port VLAN must be the same VLAN as uplink device access port

It'll take several minutes, and console could be timeout, please use command

Idle-timeout to set time limit

Is you sure-add standard port (s)? (y/n) [N]:y

The total of the VLANs has been processed is 4

The total of the port VLAN (s) has been added is 4

Create a business virtual port.

Create a business virtual port with index numbers of 2, 3, and 4, corresponding to User-vlan 2, 3, and 4,s-vlan 100, 103, 102, respectively, 7, 8, 9 for the business flow template.

(config) #service-port 2 vlan 0/1/1 multi-service User-vlan 2 rx-cttr 7 tx-cttr 7

(config) #service-port 3 VLAN 103 ETH 0/1/1 multi-service User-vlan 3 rx-cttr 8 tx-cttr 8

(config) #service-port 4 VLAN 102 ETH 0/1/1 multi-service User-vlan 4 rx-cttr 9 tx-cttr 9

Description

At this point, the Internet/voip business configuration is complete, the next steps for the IPTV service multicast configuration.

Configure multicast data.

Configure the multicast VLAN and multicast mode.

(config) #multicast-vlan 101

(CONFIG-MVLAN101) #igmp mode proxy

Is you sure to change IGMP mode? (y/n) [N]:y

Configure the multicast upstream port.

 (config-mvlan101) #igmp Uplink-port 0/0/1

Configure the multicast program.

(CONFIG-MVLAN101) #igmp program add name program1 IP 224.1.1.1 sourceip 10.10.10.10

Configure the multicast user.

(CONFIG-MVLAN101) #btv

(CONFIG-BTV) #igmp user add Service-port 3

(CONFIG-BTV) #multicast-vlan 101

(CONFIG-MVLAN101) #igmp Multicast-vlan member Service-port 3

Save the data.

(CONFIG-MVLAN101) #quit

(config) #save

Operation result

After the relevant upstream and downstream devices are configured, all three types of services on the 0/1/1 port will work.

Dial with PPPoE dial-up software on a PC, and after a successful dial-up, the user can access the Internet network.

VoIP users can talk to each other normally.

IPTV User: 0/1/1 port users can watch the program program1.

ONU MA5620 Configuration service shunt (voip,iptv,internet)