The computer boot appears blue screen to crash How to do? Blue screen crash solution

1. In the presence of the above interface, press and hold the power switch 10 seconds forced shutdown, confirm the shutdown, click again to open the key, and continuously click on the keyboard F8 key, until the Advanced Options menu (as shown below). The keyboard in the lower right corner of the key "↓" key to select "Safe mode" Press "enter", and then select the current system, press "enter";

2. About 30 seconds after entering the Select Account interface, select the Administrator account login system, as shown below:

3. After entering the system will pop up "Windows is running in safe mode," The prompt, please left click "Yes";

4. Enter the system security mode of the desktop, and then left click on the "Start"---> "Control Panel"---> "Add or Remove Programs";

5. Add or Remove Programs page, check "Show Update"---> Find "KB2859537", select "Delete";

6. Select Next in the wizard to complete the deletion. At this point the computer will automatically restart, you wait 50 seconds, you can normally use the computer.

look at what the code is: check with the following

(1) 0x0000001e (0xc0000005 0xfde38af9 0x00000001 0x7e8b0eb4) kmode_exception_handled * * * The first part of the error is the stop code (stop code) is 0x 0000001E to identify the type that has occurred. The second part of the error is a set of four digits enclosed in parentheses, representing random developer-defined parameters. Reading blue screen Stop code: (1) 0x0000000a:irql_not_less_or_ Equal is primarily caused by faulty drivers, defective or incompatible hardware and software. Indicates that there is a high level of process internal request (IRQL) in kernel mode that accesses memory addresses that have no access to them.
(2) 0x00000012:trap_cause_unknown If you encounter this error message, unfortunately, because the result of Kebugcheck analysis is unknown to the cause of the error. (Installation of innovative sound cards may be raised)
(3) 0x0000001a:memory_management This memory management error is often caused by hardware, such as newly installed hardware, memory itself has problems
(4) 0x0000001ekmode_exception_not_handledwindows kernel Check with an illegal or unknown process instruction, this outage code generally by the problem of memory or with (1) similar cause
(5) 0x00000023:fat_file_system0x00000024:ntfs_file_system0x00000023 usually occurs when reading and writing a system partition that uses the FAT16 or FAT32 file system, while the 0x 00000024 is due to an error in the Ntfs.sys file. The two blue screen errors are most likely the result of physical damage to the disk itself or disruption of the packet (IRP), which may include excessive disk fragmentation and too frequent file reads and writes. And the amount of data is very large or caused by some disk-mirroring software or antivirus software.
(6) 0x00000027:rdr_file_system The cause of this error is difficult to judge, however, the Windows memory management problem is likely to lead to the occurrence of this outage.
(7) 0x0000002e:datd_bus_error system memory memory parity error, usually due to defective memory (including physical memory, level two cache or video card memory) device driver access to the non-existent memory address, and other reasons, in addition, the hard drive is damaged by viruses or other problems, This stop code will also appear
(8) The reason for this 0x00000035:no_more_irp_stack_locations is that there is a problem with the driver itself, or that there is a quality problem with the memory
(9) 0x0000003f:no_more_system_ptes a system memory management related errors, such as: due to the implementation of a large number of I/O operations, resulting in memory management problems, defective driver incorrectly use of memory resources; An application is allocated a large amount of kernel memory, and so on.
(a) 0x00000044:multiple_irp_complete_requests is usually caused by a hardware driver (this is not a common stop code, which is caused by falstaff.sys files in a newly installed driver)
(one) 0x00000050:page_fault_in_nonpaged_area problematic memory (including: physical memory, Level two cache, video memory), incompatible software (primarily remote control and antivirus software), corrupted NTFS volumes, and problematic hardware
(a) 0x00000051:registry_error This stop code indicates that the registry or System Configuration Manager has a crop, because the hard disk itself has a physical bad path or a file system problem, resulting in the read and write registry file is an I/O error
(0x00000058:ftdisk_internal_error) indicates that an error occurred in the primary drive of a fault tolerant set.
(0x0000005a:critical_service_failed) A very important system service failed to start. (0x0000006f:session3_initialization_faled) This error usually occurs when Windows starts, typically caused by a faulty driver or corrupted system files.
(0x00000076:process_has_locked_pages) typically because a driver does not release the memory it occupies properly after an I/O operation has been completed
(0x00000077:kernel_stack_inpage_error) The kernel data that you need to use is not found in virtual memory or physical memory. This error often indicates a problem with the hard disk, the corresponding data is damaged or virus attack
(0x0000007a:kernel_data_inpage_error) This error is often caused by an independent read of kernel data in virtual memory. The reason may be that there are bad clusters in the virtual memory paging file, viruses. disk controller error, memory problem.
(0X0000007B:INACCESSIBLE_BOOT_) Devicewindows the system partition or boot volume cannot be accessed during startup. Typically occurs the first time after a motherboard has been replaced. The main reason is that the IDE controller of the new motherboard and the old motherboard uses different chips. Sometimes it can be caused by a virus or a hard drive damage.
(0x0000007e:system_thread_exception_not_handled) The system process generated an error, but the Windows error handler could not be caught. It causes a lot of reasons. Includes: Hardware compatibility, problematic driver or system services, or some software.
0x0000007f:unexpected_kernel_mode_trap is usually caused by faulty hardware or some software, and overclocking can cause this error.
0x00000080:nmi_hardware_failure is usually caused by hardware.
(0x0000008e:kernel_mode_exception_not_handled) A kernel-level application generated an error, but the Windows error processor was not captured, typically a hardware compatibility issue
0x0000009c:machine_check_excepyion is usually caused by hardware, typically because of overclocking or hardware problems (memory.) CPU-Bus-power supply)
0x0000009f:driver_power_stste_failure are often associated with power supplies and often occur in connection with power supply operations. (Shutdown, standby, sleep)
(0x000000a5:acpi_bios_error) typically because the motherboard BIOS does not fully support the ACPI specification
(0x000000b4:video_driver_init_failure) This Stop message indicates that Windows does not have access to the graphics interface because it is unable to boot the graphics driver, or that there is a hardware conflict with the video card (parallel or serial port conflicts)
(0x000000be:attempted_write_to_readonly_memory) A driver attempts to write data to read-only memory, usually when a new driver is installed. System services or the firmware program for the device has been upgraded.
(0x000000c2:bad_pool_caller) A kernel-layer process or driver incorrectly attempts to perform a memory operation, usually caused by a driver or software that has bugs
(a) 0x000000ce:driver_unloaded_without_cancelling_pending_operations is usually caused by a problematic driver or system service