The role of version Serial.flush () prior to arduino1.0 is to empty the serial cache (dropping received incoming data). But after 1.0 the function of version Serial.flush () is adjusted in order to wait for the serial port data to be transmitted (Waits for the transmission of outgoing Serial data to complete.) (Referenced from http:// Arduino.cc/en/serial/flush).Because I am in the process of using Wifibee, if both want to use serial.print through the serial port to the WiFi module to send instr
1. Windows key + R, input shutdown.exe/r/o/f/t 002. The computer will restart automatically, enter the screen, select Troubleshoot(Reprint please specify original: Http://www.harleygwak.com/wp-admin/post.php?post=187action=edit)3. Select Advanced Options4. Select Startup Settings5. Click Restart6. Press F7, or press the number 7 button directly8. The computer will automatically reboot into the system, the following can be installed under the Win7 system installation of the
Source of demand1. My son finished the year 6 years old, like to play fireworks, but the courage is small, so I am responsible for ignition, from the year before 26 to the beginning of eight, every night to give his son point firecrackers ah point firecrackers.2. The new year to open the door gun and opened the gun, Lunar New Year early morning also to help mom point firecrackers, said the whole string of small firecrackers also fried too fast, every time did not run a few steps on the open, bro
This is a old Arduino 3G module bought half years ago.Its wiki:Http://wiki.iteadstudio.com/ITEAD_3G_ShieldIts mall:Http://imall.itead.cc/itead-3g-shield.htmlDatasheet for Itead 3G Shield Http://pan.baidu.com/s/1ntCH4UHSchematic for Itead 3G Shield http://pan.baidu.com/s/1pJ5lRztDemo Code for Itead 3G Shield http://pan.baidu.com/s/1gdyaCYfIts back where you insert a SIM card:This board uses at commands to control itself.Key:at commandsWhat's AT command
Problem: arduino:1.6.3 (Windows 7), board: "Arduino Pro or Pro Mini, ATmega328 (5V, MHz)" Sketch uses 846 bytes (2) of program storage space. Maximum is 30,720 bytes. Global variables use 9 bytes, (0%) of dynamic memory, and 2,039 bytes of local variables are remaining. The maximum is 2,048 bytes. AVRDUDE:STK500_RECV (): Programmer is not responding Avrdude:stk500_getsync () Attempt 1 of 10:not in Sync:resp
First Arduino default I²c address is 7-bit address, the manual is described, 7-bit address is 0x1e, read address is 0x3d = (7-bit address If you want to communicate with the hmc5883l, you need to hmc5883l power on the 5ms. Therefore, the general write configuration requires a delay of 5ms before communication. After connecting the device to test the sensor, identify the operation and identify register a, identify register B, identify register C is
Recently suddenly want to study STM32, see almost all of the tutorials are used in C-Series microcontroller program, so that has been studying C 艹 I write very not adapt to, today studied for a noon, successfully a single LED driver package into an Arduino-style class library, the use is very convenient, the method is as follows.Before you begin, it is recommended that you follow the methods described in this article in the STM32 template creation met
Arduino relatedArticleNow,
I recently bought a Bluetooth chip (bluetooth module JY-MCU) online, which is also 37 yuan cheaper
This chip uses the Bluetooth serial port service, which is encapsulated by Arduino.
That is, the connection line reads data and writes data through the serial API,ProgramCodeIt is also very simple
The only trouble is that you can write applications on your mobile phone. I
Arduino Port Code:
int red=255; Create variables to store the data to be sent
int green = 2;
int blue = 3;
void Setup ()
{
serial.begin (9600);//define a data transfer rate of 9600 bits
}
void Loop ()
{
serial.print (red);
Serial.print (",");
Serial.print (green);
Serial.print (",");
Serial.print (blue);
Serial.print ("\ n");
Delay (+);
}
Above red, Green,blue is replaced with the value obtained by the color sensor in the actual app
Bh1750fvi is a digital ambient optical sensor IC produced by Rohm semiconductor in Japan. Its main features include:
I2C digital interface, supporting a maximum rate of 400 kHz
Illuminance)
Measurement Range: 1 ~ 65535 Lux, minimum resolution
Power down
Shielding illumination variation interference caused by 50/60Hz Mains Frequency
Two I2C addresses are supported and selected through the ADDR pin.
Small measurement error (maximum precision error +-20%)
Circuit connection
Because the modu
); Kinect = new Simpleopenni (this); Kinect.enabledepth ();}Fourth step: Under 3D rendering, draw the point cloud and the frustum (that is, the 3D area visible on the screen. The Kinect frustum means the area that Kinect can see in space. )void Draw () { kinect.update (); Background (0); Myorbit.pushorbit (this); Drawpointcloud (); Kinect.drawcamfrustum (); Myorbit.poporbit (this);}Fifth step: Finish plot point cloud functionvoid Drawpointcloud () { int[] Depthmap =
Summarize the experience of wireless module debugging. There are already people on the Arduino who have made the library of this module, but according to the manual written also has a certain reference significance.Wireless module is one of the modules that I think is more difficult to debug, because it is a module of mutual interaction, communication failure has two reasons, can not be found from a single code. The code is written, and all sorts of i
I. List of components
Arduino Pro Mini
GY-30
Second, the wiring
Using IIC communication mode, GY-30VCC connect +5v,gnd grounding. GY-30 SDA, SCL respectively A4, A5
Third, the source code
#include
Hello everyone, I'm a small-story.Remember the previous section click the Open linkToday we talk about sensors.Today, we talk about light and ultrasound.Send a picture first:The light sense has three interfaces, namely:UCC, out, GND.The ultrasound
Reprinted please indicate the source: http://blog.csdn.net/lxk7280
First, contact the kinectorbit camera library. The download URL and brief introduction of this library are provided in this article: http://blog.csdn.net/lxk7280/article/details/3818
I wrote it here, but it hasn't been tested yet.
1. Move the two ends of the led to the center and return to the two sides.
1 // adr301.ino 2 3 byte ledPin[] = {4, 5, 6, 7, 8, 9, 10, 11, 12, 13}; 4 int ledDelay(65); 5 int direction = 1; 6 int
The content source of this page is from Internet, which doesn't represent Alibaba Cloud's opinion;
products and services mentioned on that page don't have any relationship with Alibaba Cloud. If the
content of the page makes you feel confusing, please write us an email, we will handle the problem
within 5 days after receiving your email.
If you find any instances of plagiarism from the community, please send an email to:
info-contact@alibabacloud.com
and provide relevant evidence. A staff member will contact you within 5 working days.