averatec c3500

gigabit and routing capabilities are not very important, so the two 2948 switches are not used much in actual projects. 2. Mid-range products Let's look at the mid-end products. The 3500 series of mid-end products are widely used and representative. The basic features of the C3500 series switches include a backboard bandwidth of up to 10 Gbps and a forwarding rate of 7.5 Mpps. It supports 250 VLANs, IEEE 802.1Q and ISL Trunking, and CGMP/Gigabit E

series switches are generally used at the low end of the network. The gigabit and routing capabilities are not very important, so the two 2948 switches are not used much in actual projects. 　 2. Mid-range productsLet's look at the mid-end products. The 3500 series of mid-end products are widely used and representative.The basic features of the C3500 series switches include a backboard bandwidth of up to 10 Gbps and a forwarding rate of 7.5 Mpps. It s

used much in actual projects. 2. for mid-end products, refer to mid-end products. The 3500 series of mid-end products are widely used and representative. The basic features of the C3500 series switches include a backboard bandwidth of up to 10 Gbps and a forwarding rate of 7.5 Mpps. It supports 250 VLANs, IEEE 802.1Q and ISL Trunking, and CGMP/Gigabit Ethernet switches, optional redundant power supply. However, the biggest feature of

5000/5500, with 48 10/100 Mbps adaptive Ethernet ports and 2 Gigabit Ethernet ports, 24 Gbit/s back-board bandwidth, redundant power supply with hot swapping, with a series of fault tolerance features and network management features. C 2948G-L3 is added with layer-3 switching capability based on C 2948G, and the maximum layer-3 packet throughput can reach 10 Mpps. However, in general, the 2900 series Cisco switches are generally used at the low end of the network. The gigabit and routing capabi

: Unplug the power cord after the switch. Press and hold the mode key on the left side of the switch panel (generally the switch is the key), and insert the power plug behind the switch to power the switch. Wait until you see that the Ethernet indicator lights that are not wired on the switch panel are on and several system indicators of the switch are on. 　　 　　 Step 5:Enter: 　　 Switch: flash_init 　　 The following prompt is displayed: 　　 Initializing Flash... 　　 Flashfs [0]: 1 files, 1 directori

/wKiom1WpvvKhJsZXAABwiZGj0o4117.jpg "title=" Image.png "alt=" Wkiom1wpvvkhjszxaabwizgj0o4117.jpg "/>2.CISCO Router Model descriptionLow-grade: C2600 series, C2800 seriesMid-range: C3600 series, C3800 series, C3900 seriesUpscale: C7200 series, C7600 series3.CISCO Switch Model DescriptionLow: C2900 SeriesMid-range: C3500 series, C3700 seriesUpscale: C6500 series, C7600 seriesSecond, the device hardware architecture1. Router Hardware architecture① Comput

) C25fx Cisco 2500 fixed configuration FRAD C2600 Cisco 2600 series routeTool C2800 Catalyst 2800 series switches C2900 Catalyst 2900XL series switches C2950 Catalyst 2950 series switches C29atm Catalyst 2900 ATM Switch C3500 Catalyst 3500xl series switches C3550 Catalyst 3550 series switches C3620 3620 routeTool C3640 3640 routeTool

than or equal to the lower limit. When the forwarding rate of broadcast, multicast, or unicast packets is lower than several packets per second (pps), the port will resume transmission. Value Range: 0.0 ~ 10 000 000 000.0. If the value is large, k, m, or g headers can be used for representation. Example: When the bandwidth usage is 30%, the broadcast package is blocked (generally only one upper limit is entered, and the lower limit is kept by default). Example: When the bandwidth usage is 30%,