SATA interface.
8. Q: it is said that SATA hard drive supports hot swapping. Can this function be used?A: currently, the SATA technology is divided into V1.0 and V2.0 versions. V1.0 does not support hot swapping, and
During the USB flash drive operation, sometimes we encounter a USB flash drive prompt"
Unable to stop general volume", In this case, many users
Hot USB flash driveThe USB flash drive can be quickly unplugged, but this may cause data loss of the USB flash drive. Is there an
to support NCQ. In addition, NCQ technology does not support the FAT file system, only the NTFS file system is supported.As the SATA device market is chaotic, many SATA device providers abuse the "SATA II" in the marketing campaign, such as some of the "SATA II" hard drives are supported only 3Gbps and not support NCQ
prices are too expensive.
The actual transmission speed changes little.
Users to pursue mature, stable products.
This column more highlights: http://www.bianceng.cnhttp://www.bianceng.cn/Servers/zs/
SATA hard disk, serial connection, Serial ATA bus using embedded always signal, with stronger error correction capability, improve the reliability of data transmission. It also has the advantages of simple structure and
corresponding transmission speed is 150mb/s and 300mb/s. SATA is primarily used for PATA interface technology that has replaced bottlenecks. From the speed of this point, SATA in the transmission mode SATA is also more advanced than Pata, has been far away from the PATA hard drive behind. Second, from the data transmi
Motherboard SATA connector does not recognize the hard drive reasons and solutions:
One, the hard disk can not use the fault
1, BIOS setup Error
Mainly in the BIOS on the SATA Setup error, especially some early motherboards using a Third-party sata/raid control chip, but basically in the BIOS is closed, so to use th
Like old SCSI and SATA technologies, SAS supports hot-swappable disks, which is important for environments that maintain high availability requirements. And SAS is a complete two-way system, while SATA inherits the IDE's characteristics and is a system of half-two-way communication. Therefore, the SAS system throughput can be similar to the
compatible with the PATA device by using a multi-purpose chipset or serial-parallel converter. Because SATA and PATA can use the same drive, you do not need to upgrade the operating system or perform other changes.
5. You do not need to set the jumper of the Master/Slave disk for Sata. The BIOS will number it in the order of 1, 2, and 3. This depends on the
Many friends have acquired a notebook and encountered some difficult problems.
Usually install XP when the blue screen or install half of the time the copy file failed! This is generally the problem of hard disk, here is not to say hard disk physics problems, software problems. Serial ATA hard disk, Serial ATA bus with embedded clock signal, with a stronger ability to error correction, compared with the past the biggest difference is that the transmission command (not just data) to reflect, if
Sata's full name is serial Advanced Technology attachment (Serial Advanced technology Attachment, an industry-standard serial Hardware driver interface), which is made up of Intel, IBM, Dell, APT, The hard disk interface specification proposed by Maxtor and Seagate Corporation. The Serial ATA 1.0 specification was formally established in 2001 by the Serial ATA Board of Intel, APT, Dell, IBM, Seagate, and the major vendors.
SATA support
multi-language support package, with a total of 3 CDs. The simplified Chinese, traditional Chinese, and Korean language packs are in 3rd CDs, which can also beHttp://download.microsoft.com/download/fdafdac56ee-928a-Download 4d51-9d6d-c7c64e9f5baARMMUIx3.iso. Install 64-bit XP on SATA hard drive1. You must use a CD-ROM for boot installation.First, the Tester Used winrarto release ws03sp1_rtm_1830_px6_en.isoto a directory and double-click setup.exe to
After Windows 7 is installed, When you enable the AHCI function of the SATA hard disk in the BIOS, the system will fail to start. The system will recover to normal only after you change to the IDE (ATA) mode. If Windows is installed in IDE mode, you need to reinstall the system to change the hard disk to AHCI mode in BIOS. This allows many users to reload data.I. Introduction to AHCI
AHCI (Serial ATA Advanced Host Controller Interface) Serial ATA Adva
created by Udevstart are set by the rules specified by the files in the/etc/udev/rules.d/directory. If Udev cannot find the permission file for the device you are creating, set its permissions to the default of 660, and the owner is root:root. Once the above steps are complete, the devices that already exist and are built into the drive are ready to use.
For module-driven devices, when the kernel detects a new device connection, the kernel pr
Hot swapping (hot-ging or Hot Swap) is charged, and hot swapping isAllow users to take out and replace damaged hard drive, power supply or board components without shutting down the system or power supply, this improves the system's timely disaster recovery capabilities, sca
These days the test found a very strange problem if the TF card inserted into the card and then inserted into the board after hot plug can be mounted on but the use of a USB stick only when the first plug-in can be mounted on the pull down after the plug in the drive can be
The content source of this page is from Internet, which doesn't represent Alibaba Cloud's opinion;
products and services mentioned on that page don't have any relationship with Alibaba Cloud. If the
content of the page makes you feel confusing, please write us an email, we will handle the problem
within 5 days after receiving your email.
If you find any instances of plagiarism from the community, please send an email to:
info-contact@alibabacloud.com
and provide relevant evidence. A staff member will contact you within 5 working days.