A summary of experimental three (real-time system porting)

Summary of three problems in experiment

• Issues Link: 20145327 "the foundation of Information Security system Design" transplantation of three real-time system
• • How the development board goes into Linux and vv mode
    After the board is successfully connected, enter the Linux mode, type any other key, and enter the VV mode if you type enter the ENTER key
  • EXP11 Compilation failed
    This is because there are exp11_data folders in the code folder that can be compiled successfully after deletion
  • Install Ads (install files in 00-ads1.2 directory, crack method 00-ads1.2\crack directory)
    Note that the original installed ads will be uninstalled and then reinstalled before the installation can be successfully
  • On the two machines did not succeed in the last step, changed the classmate's computer succeeded.
• Problem Link: "The foundation of Information Security system Design" experiment Three

  • 1. An error occurred while make. After we check the confirmation path without Chinese, the installation prompt deletes the Exp11_data folder located in the 04-test folder. After the link succeeds.

    2, after pressing the Debug key, appears warning prompt box, after asking the teacher to know is the drive not to install, later installs several times the drive finally succeeds!

• Issues Link: 20145231 20145205 "The foundation of Information security system design" the third experiment

  • Question one: everything goes well. You cannot display graphics on the screen after you click Run.

    Resolution: Step-by-step steps to look for possible errors, discover that you have installed the Jtag.exe file and install it as per the steps in the instructions for use, but forget to initialize it, you cannot simulate debugging it. After the steps have been processed successfully, the code is compiled and run again in the same way as the instruction interface. However, there is a new problem, that is, after running the following interface, the final discovery is to set the processor model in the Uarmjtag after the change, change back to ARM9 that the operation was successful.

• Issue Link: Beijing Institute of Electronic Technology (BESTI) Experimental report 3

  • (1) Ads cannot be installed

    WORKAROUND: You need to click the Setup.exe file under the 00-ads1.2 folder under the Exp3 file, first

    (2) After setting the ARM9, HyperTerminal suddenly becomes the Linux mode from the Vivi mode.

    Solution: After consulting the teacher, the teacher said we need to restart the solution, did solve the problem, but do not know what the reason.

    (3) test , the first run, the program is normally stopped in the main function there, which is again press run, the reaction on the host and the instructions in the steps, but there is no reaction on the experimental box?

    Solution: After consulting the teacher, the teacher suggested that we change a test box to try, I just good-looking have a classmate stuck, he let me help him tune, he also has not appeared the correct result, but also with us, before all can, but the last step, the experiment box did not show the waveform, so I again on his computer, re-done again Finally, there is the same problem, but also came to the last step, the waveform can not be displayed, helpless, I had to change a before has been successfully made to the waveform of the machine, I re-boot, redo again.

    (4) Install JTAG driver only decompression not installed

    In my fourth time to start re-doing this experiment, see the time is about to 6, I was a little flustered, in the last time ADM debugging, error, has been showing errors, and later in the classmate's reminder, I remembered this time forgot to install JTAG driver, after installation, finally smooth appearance of the waveform diagram. The final waveform is shown.

• Problem Link: "The foundation of Information security system Design" experimental report of three experiments

  • • Failed to load and later found to be a JTAG JTAG driver installation Issue

      Solution: Uninstalled the re-driver installation

      Later reinstall can not be loaded successfully, and then found in the C disk has a few drivers, open use with the installation is not the same, resulting in the failure to load, figured out later solved the problem.

    • The same problem when installing the JTAG driver also encountered running Uarmjtag2.0.exe and did not install the driver, just the driver decompression, the final debugging failed, and then re-add the driver, and carry out the simulation test.

• Issues Link: 20145329 "the foundation of Information Security system Design" transplantation of three real-time system

  • 1. HyperTerminal cannot connect
    Solution: Plug back to the computer's original network cable, restart the computer, open the HyperTerminal again, enter the command line interface and then open the test box switch, power on, press any key to let Super terminal in Vivi

    2. The system cannot automatically appear and stop in the main function
    WORKAROUND: Do not configure the Axd separately in advance, wait for the debug to be configured after the Axd, debug again after configuration

    3. Test box LCD frequency can not be drawn waveform
    FIX: Turn off Uarmjtag and then turn it back on

• Problem Link: 20144303 20145239 experiment Three

  • In the experiment, the load was unsuccessful after the first point of Debug. The problem is resolved after uninstalling the JTAG driver and reinstalling it as required in the lab instructions.

    The experiment is relatively smooth, did not encounter anything larger than the problem, as long as the instructions in accordance with the requirements of the book, carefully complete each step of operation, do not miss any details, the experiment can be successful.

• problem Link: 20145312 "the foundation of Information Security system Design" transplantation of three real-time systems

  • Issue one:

    When you open Arm–flash Downloader, the pop-up prompt does not install the driver correctly.

    FIX:

    Read the UarmJtag2.0 usage instructions in detail. The Jtag driver installation method was found to be incorrect after PDF. After the installation, the driver solves the problem.

    Issue two:

    Debug An instance in the ADS software, click the Debug button always error.

     

    Fix:

    Check that driver Giveio is not installed, reinstall and then click Debug Emulation succeeded

    Question three:

    Follow step Fourth of the "03-Test Document" procedure, that is, after you have selected the files that need to be compiled, click Make, compile the link fails, there are no 4 warnings and 15 additional information, but a compilation error occurs.

    Solution: The ucos-ii in the

    04-text folder is not deleted, the initial path to the 04-text folder is on the desktop, and the files compiled in the ADS software do not recognize the Chinese path.

    Modified after the error: Copy the 04-text folder to the F-packing directory, re-select the files that need to be compiled and click Make to compile the link, the compilation will be able to show the correct compilation results.

    Iv. Experimental experience

    This experiment focuses on the migration of real-time systems and the operation of an instance. Unlike previous experiments, there are new requirements for HyperTerminal configuration without the use of operations in Redhat virtual machines. In the experimental process, the group of students in accordance with the steps of the experimental instructions to install Ads,giveio driver, Jteg driver and other software, and debugging to achieve the teacher to provide examples, in the experiment very good learning the use of several software methods and functions, for the future study laid a good theoretical foundation.

    After this experiment, the team members of the experimental platform and the construction of the Super terminal is already more skilled, but in the course of the experiment due to neglect of some details, resulting in some of the test errors, the process of error, warned us to the next experiment must be rigorous, once due to negligence, There is a good chance of unforeseen and correcting errors, when the experiment fails and only restarts the machine from the heart to configure the environment.

• Problem Link: 20145229&20145316 "the foundation of Information Security system Design" transplantation of three real-time system
  • • 1. Click Make to compile, the result of the compilation error

    • Workaround: Delete the Exp11_data folder

    2. A little penguin appeared on the board.

    • Workaround: After the arm is configured to appear in the Vivi, quickly press any key to stay in the Vivi key

    3. Need to configure after opening Uarmjtag, no icon found

    • Workaround: After the classmate tips found in the lower right corner of the computer
• Problem Link: 20145218&20145240 "the foundation of Information Security system Design" transplantation of three real-time system

  • 1. When you install ADS, the License Wazird dialog box does not appear. And the installed program is not available.

    • You need to clear the old ads version first. So we re-installed the ads; Select the Remove option in the option "Install", "Repair" or "Remove" in the installation mode, and you can install the hack method.

    2. Until the test step, the first run, the program normally stops at the main function, which is again press run, the reaction on the host and the guidance step, but the experiment box is not responding.

    • We had no problem with the previous steps, so we changed a test box, starting from the beginning, this time the success of the waveform.
• Issues Link: 20145219 "the foundation of Information Security system Design" transplantation of three real-time system
  
  
  • • Question 1: After installing ads, nothing bounces out and does not know where to crack.
    • WORKAROUND: I followed the method of looking for the software, found the Ads folder in the Start menu bar: Click Start > All Programs > Locate the ADS program > click the third item in the folder "ARM License Wizard".
    • Question 2: Do not know how to let the experimental platform to stop in the state of Vivi.
    • Solution: Ask the classmate, he told us, casually press a key can let it stop ...

    • Question 3: Do not know how to initialize the configuration in Uarmjtag, we double-click the icon after it pops up a dialog asks us to initialize the configuration, but there is no popup page ...
      

    • Workaround: Finally find the configuration page in the lower right corner of the computer screen formed a small icon, click on it can be configured.

• Issues Link: 20145310 "the foundation of Information Security system Design" transplantation of three real-time system
  • The JTAG driver must be the same as installing the Giveio driver, otherwise the driver is not installed when the software is opened.
• problem Links: 20145208 20145230 20145235 Migration of the three-real-time system of the basic design of information security system
  • • (1) Related software and driver installation issues
      • ads and JTAG are already installed on the computer we're using, which leads us to fail the first time we try to install ads, so ads need to be uninstalled and installed before they can be used; to just in case, all the drivers are reinstalled at the end.
    • (2) EXP11 compilation failed
      • This is because the code folder has a Exp11_data folder that can be compiled successfully after it is deleted.
    • (3) Jtag drive problem
      • Jtag is already installed, even if two or more installations are installed, and still cannot be compiled correctly. The workaround is to uninstall all Jtag reinstallation, because there are fewer copies or errors during the installation process, which can be resolved after the installation is properly re-installed.
    • (4) compile normally but not run out of results
    • guessing might be a driver problem, just a different computer.
• Issues Link: 20145315 20145304 "The foundation of Information Security system Design" transplantation of three real-time system
  • 1. When you install ads, you need to uninstall and reinstall, run Setup.exe when uninstalling, and select Uninstall.
    2. When installing the JTAG drive, run the Uarmjtag2.0.exe and do not install the driver, just unzip the drive, need in the Control Panel, select Add Hardware > Next > select-yes i have connected this hardware > Next > Check-Add New Hardware Device > next > Select Install I manually select hardware from List > Next > select-Show All devices > select-Install from disk-Browse, specify driver files, click OK, install drivers.
    3. When you configure HyperTerminal, do not press ENTER after opening the lab box, press any other key to enter the Vivi
    4. When you run the test program, if debug does not open, reload Uarmjtag
    5. If you are running a test program, you cannot stop at main and switch to a different computer.
• Problem Link: Experiment three "transplant of real-time system" 20145222 Huanghachi 20145213 Chi

  • • Unable to print image out:
      Solution: Box problem, change the box after the successful printing!

    • The load was unsuccessful and was later found to be a JTAG JTAG driver installation issue:
      Solution: Uninstalled the re-drive installation. However, later reinstallation can not be loaded successfully, and then found in the C disk has a few drivers, open use with the installation is not the same, resulting in the failure to load, figured out later on the solution.

    • Related software and driver installation issues
      Solution: We used the computer already installed ads and JTAG, which caused us to try to install ads the first time because the original computer, first need to uninstall replace the new one.

• Issues Link: 20145216 20145330 "The foundation of Information Security system Design" transplantation of three real-time system

  • Question: Follow the instructions given in the Experiment Guide, always do the final step, the normal loading completed and the code appears, but after clicking on the LCD screen always does not appear graphics

    Solution: Re-experiment with another test box, and finally successfully complete the experiment, the LCD screen appears on the display of our well-drawn graphics

• Issues Link: 20145324 20145325 "The foundation of Information Security system Design" transplantation of three real-time system
  • 1. Install ads not successful
    • After several attempts, it was found that ads should be uninstalled and then reinstalled
    1. UArmJtag2.0 was run, but was not successfully loaded during the debugging process
    • Later in the experiment package found its manual, open a look, found also need to run JTAG installation driver, after the installation is complete, you can continue the experiment behind
    1. During debugging, wait for the system to automatically jump to main, but found that waiting for a long time, and did not jump to main
    • Tried several machines, are the same problem, but the experimental process and the need to install the driver is the same as the success of the students, so decided to change the next time the computer to change arm and try again
• Problem Link: 20145224&20145238 "The basic design of Information security system" experiment three

  • 1. Problem One: The test uses make to compile the link, and the result shows an error.

    WORKAROUND: The result of the error is that after selecting EXP11.MCP, the Exp11_data folder will appear with the Make compile link, which has Chinese. So you need to first delete the original folder.

• Problem Link: 20145204&20145212 Information security system Experiment three reports

  • 1, always can not find the Uarmjtag in the configuration interface where the initialization.
    Solution: Asked the classmate only to find the original in the lower right corner of the table.
    2, after all debugging, click the Go button has not been able to show the results of the drawing.
    Resolution: After trying again 2 times without a result, we re-tested the test chamber.
• Issues Link: 20145311 "the foundation of Information Security system Design" transplantation of three real-time system

  • 1, the beginning of the installation of ads when the installation was finished but could not be opened, and then uninstalled the original version in the reinstallation can be

    2, in the start run after make, the lab will always go into the UNIX system, and we need to be the Vivi system, so we choose not to open the lab before, in the end need to run

    When you open the lab box, press any key to enter the Vivi system.

    3, then run the time will always appear to run the situation, waited for a long time also did not respond, tried several times also did not respond, finally changed a host to try a bit on it

• Issues Link: 20145221 "the foundation of Information Security system Design" transplantation of three real-time system
  • The debug operation timed out after loading a backward line on the program
    • Detailed Description:
      • Early in accordance with the operation of the experiment instructions, all the smooth, in the 5th step of operation, the program after the debug operation has not responded, always did not enter the main function, can not clickgo按钮
    • Resolution process:
      • There is no other way, you can only turn the ADS1.2 integrated development environment back on after you reopen the file and restart and configure the Jtag driver, which resolves the problem 2 or 3 times.
• Issues Link: 20145210 20145226 "The foundation of Information Security system Design" transplantation of three real-time system

  • 1. Click Make to compile, the result of the compilation error

    Workaround: Delete the Exp11_data folder

    2. Load is not successful after loading is complete

    Workaround: Reopen the file after shutting down the ADS1.2 integrated development environment and restart and configure the JTAG driver

    3. Before commissioning the program must ensure that the experiment box does not show the small Penguin, show that the small penguin experiment can not be successful

• S

A summary of experimental three (real-time system porting)