To configure a vswitch port image, experts can understand the following knowledge about the vswitch port image configuration. You only need to complete the vswitch port image configuration in a few minutes. The local connection is also mentioned in this article.
Vswitch images such as 3026]
Vswitches such as S2008/S2016/S2026/S2403H/S3026 support port-based images. There are two methods:
Method 1:
◆ Configure image observation) port [SwitchA] monitor-port e0/8
◆ Configure the mirrored port [SwitchA] port mirror Ethernet 0/1 to Ethernet 0/2
Method 2:
◆ You can define the image and the port [SwitchA] port mirror Ethernet 0/1 to Ethernet 0/2 observing-port Ethernet 0/8 at a time.
8016 vswitch port image Configuration]
◆ Assume that the mirror port of vswitch 8016 is E1/0/15, the mirrored port is E1/0/0, and Port 1/0/15 is the observation port configured for the switch port image. [SwitchA] port monitor ethernet 1/0/15
◆ Set Port 1/0/0 as the port to be mirrored, and image the input and output data. [SwitchA] port bonding ing ethernet 1/0/0 both ethernet 1/0/15
You can also mirror the input and output data through two different ports.
◆ Set E1/0/15 and E2/0/0 as image observation ports.) port [SwitchA] port monitor ethernet 1/0/15
◆ Set Port 1/0/0 as the mirrored port, and use E1/0/15 and E2/0/0 to mirror the input and output data respectively. [SwitchA] port bonding ing gigabitethernet 1/0/0 ingress ethernet 1/0/15 [SwitchA] port bonding ing gigabitethernet 1/0/0 egress ethernet 2/0/0
"Stream Image-based Data Process 』
A vswitch based on a flow image mirrors some streams. Each connection has two data streams. For a vswitch, these two data streams must be mirrored separately.
3500/3026 E/3026F/3050]
Cloudification-Based Image 〗
◆ Define an extended access control list [SwitchA] acl num 101
◆ Define a rule message source address as 1.1.1.1/32 to all destination addresses [SwitchA-acl-adv-101] rule 0 permit ip source 1.1.1.1 0 destination any
◆ Define a rule message source address as the destination address of all source addresses 1.1.1.1/32 [SwitchA-acl-adv-101] rule 1 permit ip source any destination 1.1.1.1 0
◆ Mirror the packets meeting the preceding ACL rules to E0/8 port [SwitchA] mirrored-to ip-group 101 interface e0/8
2-layer stream-Based Image 〗
◆ Define an ACL [SwitchA] acl num 200
◆ Define a packet from E0/1 to all other ports [SwitchA] rule 0 permit ingress interface Ethernet0/1 (egress interface any)
◆ Define a data packet from all other ports to E0/1 [SwitchA] rule 1 permit (ingress interface any) egress interface Ethernet0/1
◆ Mirror data packets that match the preceding ACL to E0/8 [SwitchA] mirrored-to link-group 200 interface e0/8
5516]
Allows you to configure the port Ethernet 3/0/1 as the monitoring port for inbound traffic mirroring. [SwitchA] mirror Ethernet 3/0/2 ingress-to Ethernet 3/0/1
6506/6503/6R]
Currently, the three products only support mirroring inbound port traffic. Although the outbount parameter exists, it cannot be configured. The image group name is 1, the monitoring port is Ethernet4/0/2, and the inbound traffic on the port Ethernet4/0/1 is mirrored. [SwitchA] grouping ing-group 1 inbound Ethernet4/0/1 mirrored-to Ethernet4/0/2
Additional description]
◆ Images can generally achieve high-speed switch port mirroring to configure a low-speed port. For example, a m port can be mirrored to a m port, but not vice versa.
◆ 8016 supports cross-board switch port mirroring configuration.