Bridging of the radio router relay function

I would like to introduce you to the radio router relay function settings. Many people may not know about the radio router relay function settings. It does not matter. After reading this article, you will certainly have a lot of GAINS. I hope this article will teach you more things.

Bridging of the radio router relay function

You often encounter a situation where the wireless router relay function is too large, or when you share a router with a neighbor, the signal is not strong enough. At this time, if your router has a wireless relay function, you can enable this function.

The relay function of a wireless router is as follows:

◆ The access network of the primary router, whether it is ADSL or residential broadband, is automatically set or manually set to allow access to the Internet.

◆ Select WEP encryption mode for the wireless settings of the primary router. Currently, most routers do not support more advanced encryption methods during wireless relay. WEP is an extremely insecure method and can be restricted by MAC addresses. Wireless channels cannot be set automatically. You can select any channel from 1 to 13. Setup you selected 1. We recommend that you set the Local Area Network to 192.168.1.1, mask 250.250.250.0, and DHCP should be set automatically. If not, it should be 192.168.1.2 to 192.168.1.254.

◆ The wireless router relay function is used to set the wireless relay of the router as a base station and enter the MAC address of the 2nd routers. If you do not know, please immediately write down the MAC address of the primary router.

◆ Start to connect to 2nd vrouters through a computer. The access does not require account links. Click Wireless Settings directly, select the channel, and now the wep encryption method. Set its wireless relay, select the wireless relay option, and enter the wireless MAC address of the master router. Note that either vro has two MAC addresses, one for the LAN, one is wireless. Record the wireless MAC address of the vro. In this case, the DHCP option is automatically disabled. If not, manually disable it. Set any address from 192.168.1.2 to 192.68.1.254 for the wireless relay address, which is assumed to be 192.168.1.99.

◆ Connect to the primary router. In the wireless base station, enter the wireless MAC address of the 2nd routers. Generally, multiple routers are supported.

◆ Now, when you open two routers, you will find that any Wireless wifi device can freely connect the two routers to the Internet.

◆ Solve the security problem: Since WEP is not secure, press us to enable MAC address filtering. Click Wireless Settings: Enter the mac address of each wireless device. You can use ipconfig/all to view the mac address. A mobile phone, such as an iphone, directly enters the settings-General = about the local computer, there is a MAC address. If it is not easy, let the device access it. You can view the currently accessed device and put it in the list. Then enable filtering.

◆ Tips: When the wireless names of the two routers are the same, if your wep password is the same, you will find that, your Internet access device will be able to switch between two routers freely and continuously.

◆ Remember, do not set other addresses such as 192.168.2.1 for the 2nd vrouters. In this way, you will find that you cannot manage your vrouters and can only initialize them with a toothpick.

◆ If a new computer or mobile phone needs to access the network, access 192.168.1.1 through the computer and configure the MAC access list. Access the management page of the 2nd routers through 192.168.1.99.

The above test of the wireless router relay function is the netgear router-WGR614V9. Of course if you only have one router, the encryption method directly choose WPA2-PSK (AES), the current wireless network encryption status: wep encryption is easy to crack, WPA-PSKTKIP) encryption can also crack, WPA2-PSKAES) encryption will not crack, WPA-PSKTKIP) + WPA2-PSKAES) encryption will not be cracked. Currently, China's network environment is very poor, expensive and not easy to use. If you want to share a network with others, refer to the above steps.