Categories of self-check for each system startup

Source: Internet
Author: User
Free of charge for mobile English worth RMB 880

The system performs self-check every time it is started:
CHKDSK is verifying files (stage 1 of 3)
Then CHKDSK is verifying indexes (stage 2 of 3)

Method 1:

When the instance is shut down normally, the hard disk must be self-checked after each restart. After multiple parties find the solution:
Click Start> Run. In the run dialog box, enter regedit to open the Registry Editor and select
"HKEY_LOCAL_MacHINE \ SYSTEM \ CurrentControlSet \ Control \ Session Manager" subkey,
In the window on the right, find the "BootExecute" key value and clear the value. Press "F5" to refresh the registry.
The reason may be that I used voptxp to sort out disks! Study hard!

Method 2:

Select Start> Run. In the run dialog box, type chkntfs/t: 0 to set the disk scan wait time to 0. If

To ignore scanning a partition when the computer starts, such as a drive c, you can enter the "chkntfs/x c:" command. If you want to restore

Scan. You can use the "chkntfs/d c:" command to restore all default chkntfs settings, except for the countdown of automatic file check.

.

Other possibilities:

1. disable idle IDE Channels

Acceleration principle: Because the Windows XP system will automatically detect the IDE devices on the computer during startup, the idle

IDE channel detection to accelerate system startup. However, many people think that

Disable the idle IDE channel in the BIOS. It is recommended that you disable the idle IDE channel in both the BIOS and the system. First, the first method is

It does not work because the XP operating system can bypass the BIOS of the motherboard to independently monitor various states of computer hardware.

One more action. Therefore, you can disable idle IDE channels only in Windows XP.

[Practice]: Right-click "my computer-properties", click "hardware", and then click "Device Manager" to open"

Ide ata/PATA controller "(slightly different chips), and then enter the Primary and Secondary IDE channels, select" Advanced Settings ", in

Here, find the item "Current transfer mode" is "not applicable" (this is the corresponding to the idle IDE channel), set the "device type" of this item

"To" NONE ". OK.

2. manually set IP addresses
Acceleration principle: Windows XP is developed on the basis of Windows 2000. Therefore, it supports a wide range of network functions. Here

Windows XP system automatically checks whether the computer is connected to the LAN after it is turned on. However, most users access the Internet from a single computer and connect to the network.

Basically, the IP address is automatically obtained. In this way, the system will search for the DHCP server to assign an IP address to the machine.

But generally, it is not configured. This causes the system to spend a long time searching for DHCP servers after each boot

The IP address or service will be stopped after timeout. During this period, even if you come to the desktop, the double-click program does not reflect any. This is also a lot of use

Windows XP users reported that after entering the desktop, there was a "crash" problem for more than 10 seconds! In fact, you only need to manually assign

IP addresses can easily solve this problem, avoiding automatic network detection for every boot of Windows XP, thus accelerating startup!

[Practice]: Right-click "Network Neighbor" and choose Properties. Right-click "Local Connection" and choose Properties.

Double-click "Internet Protocol (TCP/IP)", select "Use the following IP Address", and enter an IP address (for example, 192.168.0.1 ),

The default subnet mask is enough. (This will not cause any conflict with your Internet connection. This address is only used in the LAN .)

The next search will quickly find the IP address and quickly enter the system.

3. Disable devices that are not currently in use

Acceleration principle: at present, computer peripheral devices are much cheaper. Many people have bought U disks, mobile hard disks, and other products, but many of them are

After use, forget to disconnect these USB devices from the host, because Windows XP system boot will automatically detect the USB interface, so these

If the device is connected to the host at startup, the system starts slowly. I have personally experienced a friend's computer connecting to a mobile hard drive to boot

You cannot access the system after the connection is disconnected. Therefore, after using USB flash drives, mobile hard drives, and

Disconnects the host, and prevents unexpected damage to the device due to current impact (because many chassis Manufacturers

Cost, There is no necessary protection circuit on the front USB interface, or even no grounding ). In addition, if you use a notebook

If you cannot use any infrared or wireless network card, disable it in the Device Manager. Because these extended devices, especially NICs

The system startup speed is greatly affected. If this feature is disabled, the System Startup Check is skipped.

Note: because the system will automatically read the optical drive by default, the optical drive will be checked during startup,

It will be automatically read. If it is a multimedia disc, the read time will be longer, and the start time of the computer will be extended. Therefore, it is recommended to be large.

After using the CD, remember to fetch it in time.

4. Disable topic desktop Removal

Many friends like beautiful theme or wallpaper, but the beauty is costly, that is, it consumes a lot of memory and there is too much on the desktop.

The same is true for icons. Each time the system starts to display the desktop, it first needs to check whether the topic is enabled. Once discovered, it will load.

As a result, the topic consumes a large amount of memory (many other users make imperfect subjects, and many compatibility problems will occur after use.

System faults ). At the same time, the system will also find and verify the effectiveness of the desktop shortcut, so the more shortcuts, the verification time spent

The longer it is. We recommend that you do not use theme whenever possible. You can set a beautiful wallpaper at most. Then split the Desktop shortcuts

Put other classes in a dedicated folder for ease of management, and accelerate the startup!

5. Close unnecessary startup programs

Many software will automatically run some background programs after the system starts, such as Winamp and office.

These programs will make the startup slow. You should press "start-Run" and enter "msconfig" and press ENTER-"start" to close

Disable unnecessary startup items. You only need to retain the input method and firewall (based on your personal settings ).

In addition, we recommend that you do not set the memory optimization software to boot. Because not only does the boot memory not only have a very small effect, but it also seriously affects startup

The correct method is to change the name of the memory after running PhotoShop and other software that requires a large amount of memory.

Result. (In fact, the memory management of the operating system has been quite complete since Win2000, And now winXP has improved its memory management

For scientific and effective purposes, the use of memory is Limited)

6. Anti-virus software is also troublesome

Some anti-virus software provides the system startup scanning function, which takes a lot of time. In fact, if you have enabled the anti-virus software

When the monitoring function is enabled and the system is checked for viruses at regular intervals, scanning the system is redundant at startup. disable this function!

If there is no way to do this, I think a sector of your computer's hard disk is broken. Do you have dry sound when you use a computer?

It is often used to have dry sound, especially when running a program. It is generally used to have bad sectors in the disk.

Free of charge for mobile English worth RMB 880

Contact Us

The content source of this page is from Internet, which doesn't represent Alibaba Cloud's opinion; products and services mentioned on that page don't have any relationship with Alibaba Cloud. If the content of the page makes you feel confusing, please write us an email, we will handle the problem within 5 days after receiving your email.

If you find any instances of plagiarism from the community, please send an email to: info-contact@alibabacloud.com and provide relevant evidence. A staff member will contact you within 5 working days.

A Free Trial That Lets You Build Big!

Start building with 50+ products and up to 12 months usage for Elastic Compute Service

  • Sales Support

    1 on 1 presale consultation

  • After-Sales Support

    24/7 Technical Support 6 Free Tickets per Quarter Faster Response

  • Alibaba Cloud offers highly flexible support services tailored to meet your exact needs.