Concept Analysis: dBm, DBI, DBD, DB, DBC, dbuv

Source: Internet
Author: User

1. DBM

DBM is the absolute value of power. The formula is: 10lgp (power value/1 MW ).
[Example 1] If the transmit power P is 1 MW, it is converted to dBm and then 0dbm.
[Example 2] for 40 W power, the converted value in dBm unit should be:
10lg (40 W/1 MW) = 10lg (40000) = 10lg4 + 10lg10 + 10lg1000 = 46dbm.

2. DBI and DBD

DBI and DBD are the obtained Gain values (power gain). Both are relative values, but the reference standards are different. The reference of DBI is a full-direction antenna, and the reference of DBD is a dipole, so the two are slightly different. It is generally considered that the same gain is expressed in DBI, which is 2. 15 larger than that expressed in DBD.
[Example 3] For an antenna with a gain of 16 DBD, the gain is converted to 18.15dbi (decimal places are generally ignored, which is 18dbi ).
[Example 4] 0dbd = 2.15dbi.
[Example 5] the gain of the GSM900 antenna can be 13dbd (15dbi), and the gain of the GSM1800 antenna can be 15dbd (17dbi ).

 

3. DB

DB is a value that represents the relative value. When considering how many DBs with a power greater or smaller than B's power, the following formula is used: 10lg (a power/B power)
[Example 6] If the power of a is twice the power of B, then 10lg (the power of a/B) = 10lg2 = 3 dB. That is to say, the power of a is 3 dB higher than that of B.
[Example 7] 8 inch M transmission loss of the 100/GSM 900 feeder is about dB.
[Example 8] If the power of a is 46dbm and that of B is 40dbm, it can be said that a is 6 dB larger than that of B.
[Example 9] If antenna A is 12dbd and antenna B is 14dbd, it can be said that antenna A is 2 dB less than antenna B.

4. DBC

Sometimes we can see that DBC, which is also a unit that represents the relative power value, is exactly the same as the DB calculation method. In general, DBC is used to measure the relative value of the carrier power in many cases relative to the carrier power, for example, it is used to measure the relative values of Interference (same-frequency interference, Intermodulation Interference, Intermodulation Interference, out-of-band interference, etc.) and coupling and stray. In principle, database can also be used to replace DBC.

5. dbuv

According to the basic formula V ^ 2 = p * r between power and level, dbuv = 90 + dBm + 10 * log (R) and r is the resistance value.
The correct path in the PHS System should be dBm = dBuv-107 because its antenna feed impedance is 50 euro.

6. dbuvemf and dbuv

EMF: electromotive force)
For a signal source, dbuvemf refers to the port voltage when the open circuit is used, and dbuv refers to the port voltage when the load is matched.

Contact Us

The content source of this page is from Internet, which doesn't represent Alibaba Cloud's opinion; products and services mentioned on that page don't have any relationship with Alibaba Cloud. If the content of the page makes you feel confusing, please write us an email, we will handle the problem within 5 days after receiving your email.

If you find any instances of plagiarism from the community, please send an email to: info-contact@alibabacloud.com and provide relevant evidence. A staff member will contact you within 5 working days.

A Free Trial That Lets You Build Big!

Start building with 50+ products and up to 12 months usage for Elastic Compute Service

  • Sales Support

    1 on 1 presale consultation

  • After-Sales Support

    24/7 Technical Support 6 Free Tickets per Quarter Faster Response

  • Alibaba Cloud offers highly flexible support services tailored to meet your exact needs.