D-Link wireless router port ing

The radio router port ing setting is very important in the router setting. Next we will take a look at the specific method of the D-Link wireless router port ing. If it is a wired connection after the router and the computer are connected, of course, you have to connect the network cable. If you want to connect to the Internet wirelessly, you 'd better connect the network cable for the first time to avoid unnecessary troubles .)

Start the computer and router, enter the system, open the browser, enter the General wireless router port ing Default Gateway in the address bar: "192.168.1.1", and then press Enter. You may need to enter the account and password in the pop-up window. Enter the account and password in the manual to enter the user operation panel. You can change the account and password of the logon operation panel. After entering the homepage of the Operation Panel, the online setting wizard button is displayed immediately. Do not mistakenly think about the special features. In fact, the installation and Setup Wizard is just a nice name.

The password setting page is displayed. This password is the password that we used to log on to the Operation Panel. You can modify it now to avoid the trouble of being intentionally or unintentionally modified by others through the default password. Enter the default password. Then, enter the new password twice, confirm the password, and click Next. Note: Remember your password. Then we came to the time zone selection page, which is too familiar with settings. Let alone select Beijing, Hong Kong, Singapore, and Taipei Zone 8. Of course, if you are abroad, you can also select the corresponding time zone. Access the Internet at the south pole or North Pole ...... After the selection, click Next.

Then we will go to the select WAN Type page, which provides four connection options: Dynamic IP address, fixed IP address, PPP over Ethernet (PPPoE) and other WAN types. You can set it according to your actual situation. Generally, most users use the ADSL dial-up Internet connection method. Then we select PPP over Ethernet and click Next. After entering the page for setting PPPoE, we can see that there are only a few simple input boxes. In the first box, enter the account that the ISP service provider gives you, that is, the account used for dial-up Internet access, enter the password below. For the service name, do not enter it. Click Next to complete this step.

Then we came to the set wireless communication online page. First, in the wireless network ID box, enter the ID that we want to connect to the vro through wireless connection. You can enter the ID as needed to identify multiple wireless devices in the same environment. Then select the channel and encryption method supported by the wireless device. Here we select WPA-PSK. Enter a password of 8 to 64 letters in the Shared Password box below. Of course, you can also select the OPEN sharing mode, that is, anyone in the wireless coverage can use this wireless router port ing to connect to the network. Of course, we recommend that you enter the password, then enter the same password on the computer to connect to the router.

On the settings page, we have successfully completed the Setup Wizard. Click the previous step to go back to the previous page and reset the settings. Click "reactivate", save the settings in the previous steps, and activate them. Then we can access the Internet normally. After completing the simple setup wizard, you can access the Internet normally. But if we like to solve the root problem, we decided to understand the router settings. Click the wireless network button on the left navigation bar to go to the wireless settings homepage.

We can see that the page set for wireless is a bit familiar. That's right. One of the steps in the setup wizard is wireless settings. The setting content is the same as that on this page. If you want to use a wireless network, you must set the wireless end to active. The wireless network ID is used to identify the vro. Just enter your favorite ID. Select your own channel, while none is not recommended for security mode. Select other options and enter the security password. In this way, machines without passwords cannot easily connect to your network.

Then, click the WAN button to go to The WAN settings page. As we have said before in the setup wizard, generally, ADSL users use the PPPoE Method for dial-up Internet access. Select the PPPoE option and perform the following operations. Users who access the Internet in other ways can select the appropriate options.

Click PPPoE and set it in the following section. If you need to enter the MAC address of the local machine on the MAC address, you can click "Copy MAC address from the user end" to automatically obtain the MAC address of the local machine, which is very convenient. Click "dynamic PPPoE. As for PPPoE username, password, and service name, we have mentioned before that for dial-up Internet access, you only need to enter the account and password for dial-up Internet access. The IP address and the settings of the Primary and Secondary DNS servers are the same as those set in WINDOWS. You can enter the relevant IP address. The maximum idle time is 5 minutes by default. You can modify the time as needed. MTU is the maximum data packet to be transmitted. The default value is 1492. If you require MTU, do not modify it. In the online mode, we click "connection with traffic", which means that the connection will automatically come online when a program needs to access the Internet. Of course, you can choose to manually connect to Alibaba Cloud. Or you can choose to automatically keep online. Finally, the TTL value is changed and the activation status is retained. TTL (TTL) is a value in the IP protocol package. It tells the network router package whether the time in the network is too long and should be discarded. IGMP (Internet Group Management Protocol) remains active without modification. Click the execution button at the bottom to save the settings.

A few simple boxes. after entering the box, you can. The first is the IP address, which we don't need to talk about. Then there is a sub-network mask, which is actually a sub-mask. We have seen a lot on windows, which is generally 255.255.255.0. The last is the domain name. If you want to add a domain name, enter the relevant name. By default, do not enter the domain name. Finally, click the DHCP button to go to the dynamic IP Address Allocation page.

If you want the computer connected to the vro to automatically obtain the IP address, you must activate the DHCP server function. Enter the start and end IP addresses and define the CIDR blocks for Automatically Obtaining the IP addresses. The lease time is to set the time available for the assigned IP address. After expiration, it is automatically changed to another IP address. To enable the fixed DHCP function, click the activation option below and enter the corresponding information in the input box. We can also see the current dynamic and static DHCP status in the following status table. Click execute to save the settings.

The second item in the top navigation bar is advanced settings. After you click it, the set homepage is displayed, that is, the virtual server settings page. To use the virtual server function, Click Activate and enter the service name of the server to differentiate different services. Then, enter the IP address that you want to use as the server and the port ing between individuals and public wireless routers and the Protocol. Scheduling is the time when the virtual server is enabled. It can be enabled all the time, or at a specified time. Finally, we can see the added services in the virtual server list, and click the modify icon to set them.

Special application functions allow users to execute specific software under NAT. The required information is basically the same as that of the virtual server, but there is only one more trigger port segment. We can enter the wireless router port ing segment of the application. Click "Save settings. Filters are used to filter specific networks and connections. We can filter through IP, URL, MAC, and domain. After selecting different options, different input boxes will appear below, so that you can easily set them. If you want to enable the IP address filtering function, select "Activate" as the option, and enter the IP address or IP address, wireless router port ing range, and Protocol below. Then, determine the filtering time and click execute.

Then we enter the firewall settings interface. The firewall settings are basically the same as those on the computer. After activation, select allow or disable communication, enter the source and destination IP addresses, and enter the port and application time. After setting, you can select whether to enable the rule in the selection box before the list, which is convenient and easy to use.