Efficiency source Seagate Hard Drive remote maintenance case-K9K10 disk write process

Efficiency source Seagate Hard Drive remote maintenance case-K9K10 disk write process failure disk: Cool fish 10 Seagate disk. St3610815as SN:5RA2TXNW firmware Version number: 4. Aaa. Fault phenomenon and user maintenance: Just finished calibration needs to write to scan hard disk to see the bad situation. It has not been broken.

Remote connection Good user computer: Found not K9 disk, but K10 disk. Opening the Seagate Specialization Program instruction mode displays the following conditions:

The current age value can be observed with a period directly under the instruction, showing that the 4F calibration does not run through the entire process, and the process is skipped in the middle of the error.

Use the e4e command to see the exact log of this calibration!

Indeed many processes have not run, according to experience, should be re-calibrated, the user asked to write, said we did not have anything on the calibration of K9k10 after the writing of the tutorial, then we have to finish the task of writing this disk today. (If the scan still has a bad word to do calibration is not too late)

The following are the methods and procedures for writing the Seagate K9K10 disk after the calibration is completed:

First of all:

Back to the AGE50 state. Use the R command to determine if the hard disk basic resource file module is properly loaded into memory (if you go directly back to t> to indicate normal)

The judgment here is that if the error is usually the firmware area still has problems, basically need to recalibrate to repair.

T> Enter the CTRL + C command to reset the hard drive.

From the information you can see the wrong ATA module and write back to the ATA module.

Turn off instruction mode. Go to the program window interface and load the hard drive in the loading management. Use the function to write back to the original disk number 1th ATA module

K9,k10 Disk write-back ATA module A little longer than a K7 disk or other hard drive (usually in 15-30 minutes)

This requires the user to wait patiently, do not give up halfway:

The writeback process is displayed as follows: (repeated occurrences several times)

After successful write-back: Directly shut off the hard drive power:

Reset Smart ... After the wait is over, continue with the following: The status will be ready. Back to the main program interface, click the Model button, found that the model, LBA value can not be read:

It's OK, write back the original disk info module. Choose

The original disk 4th INFO module. Successful, the re-observation model, LBA can be recognized normally.

button, write back

The whole work of writing is done.

Summary: K10 K9 Disk write recognition, in the case of constant power, CTRL + C command to reset the hard disk, r command Load system resources (general test can be loaded normally, only reset can be). Load the hard drive with the specialized program. Directly write back to the ATA module, re-power off the hard drive, not to the F-level of the direct write-back info module to complete the operation. If you go to the F-level disk, you need to boot again to the t> write-back app module. Refer to the F-level tutorial On Error in the app module for specific operations.

Efficiency source Seagate Hard Drive Remote Data recovery case-Cool Fish 9 disk data recovery

Failed hard drive: K9 tlite 1_disk ROM version number s-6b

Symptom: The following instructions are shown below:

After using the specialized program to repair the CE LOG function, the power is turned off to display the following information

:

(This is the user in the Efficiency Source Forum on the graph)

I told the user to use n50,,22 carriage return to see if they could return to AGE50 mode. No effect, still after power off. Today I tell you that if you encounter a similar situation of the hard disk to do data recovery, you can directly use instructions to complete. Avoid the serious failure of a large number of hard drives and the specialized program does not completely repair CE log errors. Cause repair Celog cannot return to 50. The following is a remote operation that uses instructions specifically:

First go to t>, then ctrl+r load calibration module to memory, then input n4e,,22, enter, and finally use the Ctrl+t command to open the calibration, complete operation. The key is to manually return to N50 after completion, as shown in:

n50,,22 returns to AGE50.

Turn off the hard drive again, no error message is displayed.

The data can be viewed normally. Hehe, Summary: Specialized program is very versatile you can directly use the instructions to complete, so you can flexibly according to the breakdown of the damage of the disk, to take specific methods and measures.

Efficiency source Seagate Hard Drive remote maintenance case-K9K10 disk write process