Experiment: Huawei mux vlan configuration and management, Huawei mux
The following experiment is an experimental video teaching course designed by the author for "Huawei switch Learning Guide". Click here to view details: http://edu.51cto.com/course/course_id-2091.html
Huawei's mux vlan function enables different VLANs located in the same IP network segment.(All slave and master VLANs)Users can achieve layer-2 isolation between different slave VLANs, as well as layer-2 isolation between users in the same VLAN on the same switch. users in the same VLAN on different switches are not isolated.This technology can be used to isolate different user hosts in the same VLAN while sharing user servers in multiple VLANs..
The following is a specific experiment solution.
Lab environment: PC1 ~ 6. The Server and the Server are both in the same IP segment and are divided into the corresponding master or corresponding types of VLAN as shown in the figure.
Lab requirements: each slave VLAN host can directly access the Server, but each slave VLAN cannot directly access each other, and PC2 and PC3 in VLAN20 cannot communicate with each other, however, both of them can communicate with the PC4 of the same VLAN20.
Experiment Configuration:
• SW1 Configuration
<Huawei> sys
[Huawei] sysname SW1
[SW1] vlanbatch 10 2030 40
[SW1] vlan40
[SW1-VLAN40] mux-vlan
[SW1-VLAN40] subordinategroup10 30
[SW1-VLAN40] subordinateseparate20
[SW1-VLAN40] quit
[SW1] interface GigabitEthernet0/0/1
[SW1-GigabitEthernet0/0/1] port link-typetrunk
[SW1-GigabitEthernet0/0/1] porttrunk allow-pass vlan 10 2030 40
[SW1-GigabitEthernet0/0/1] quit
[SW1] interface GigabitEthernet0/0/2
[SW1-GigabitEthernet0/0/2] port link-typetrunk
[SW1-GigabitEthernet0/0/2] port trunkallow-pass vlan 10 2030 40
[SW1-GigabitEthernet0/0/2] quit
[SW1] interface GigabitEthernet0/0/3
[SW1-GigabitEthernet0/0/3] port link-typeaccess
[SW1-GigabitEthernet0/0/3] portdefault vlan 40
[SW1-GigabitEthernet0/0/3] port mux-vlanenable
[SW1-GigabitEthernet0/0/3] quit
• SW2 Configuration
<Huawei> sys
[Huawei] sysname SW2
[SW2] vlanbatch 10 20 30 40
[SW2] vlan 40
[SW2-VLAN40] mux-vlan
[SW2-VLAN40] subordinate group 10 30
[SW2-VLAN40] subordinate separate 20
[SW2-VLAN40] quit
[SW2] interface Ethernet0/0/1
[SW2-Ethernet0/0/1] port link-type trunk
[SW2-Ethernet0/0/1] port trunk allow-pass vlan 10 20 30 40
[SW2-Ethernet0/0/1] quit
[SW2] interface Ethernet0/0/2
[SW2-Ethernet0/0/2] port link-type access
[SW2-Ethernet0/0/2] port default vlan 10
[SW2-Ethernet0/0/2] port mux-vlanenable
[SW2-Ethernet0/0/2] quit
[SW2] interface Ethernet0/0/3
• SW3 Configuration
<Huawei> sys
[Huawei] sysname SW3
[SW3] vlanbatch 10 20 40
[SW3] vlan 40
[SW3-VLAN40] mux-vlan
[SW3-VLAN40] subordinate group 10
[SW3-VLAN40] subordinate separate 20
[SW3-VLAN40] quit
[SW3] interface Ethernet0/0/1
[SW3-Ethernet0/0/1] port link-type trunk
[SW3-Ethernet0/0/1] port trunk allow-pass vlan10 20 40
[SW3-Ethernet0/0/1] quit
[SW3] interface Ethernet0/0/2
[SW3-Ethernet0/0/2] port link-type access
[SW3-Ethernet0/0/2] port default vlan 10
[SW3-Ethernet0/0/2] port mux-vlanenable
[SW3-Ethernet0/0/2] quit
[SW3] interface Ethernet0/0/3
[SW3-Ethernet0/0/3]Port link-type access
[SW3-Ethernet0/0/3]Port defaultVlan20
[SW3-Ethernet0/0/3]Port mux-VlanEnable
[SW3-GigabitEthernet0/0/3]Quit
Verify the experiment results:
UseDisplay mux-VlanCommand to view mux vlan configuration information
Each PC in the VLAN can ping the Server in the active VLAN.
Different from VLAN cannot be pinged
Hosts in the same isolated VLAN on the same vswitch cannot be pinged.
Hosts in the same isolated VLAN on different vswitches can still be pinged.
VLAN configuration for Huawei 5700 vswitches
Vlan batch 2 10 20 30
#
Vlan 30
Mux-vlan
Subordinate group 20
Int vlan 2
Ip add 192.168.100.1 24
QUIT
Int vlan 10
IP add 192.168.1.1 24
Quit
Int vlan 20
Ip add 192.168.2.1 24
Quit
Int vlan 30
Ip add 192.168.3.1 24
#
Interface Ethernet0/0/1
Port link-type access
Port default vlan 10
Port mux-vlan enable
#
Interface Ethernet0/0/2
Port link-type access
Port default vlan 10
Port mux-vlan enable
#
Interface Ethernet0/0/9
Port link-type access
Port default vlan 20
Port mux-vlan enable
#
Interface Ethernet0/0/12
Port link-type access
Port default vlan 20
Port mux-vlan enable
#
Interface Ethernet0/0/13
Port link-type access
Port default vlan 30
Port mux-vlan enable
For Huawei switches to divide VLANs, I need four VLANs, and three of them cannot communicate with data. One Management vlan needs to be configured.
Vlan 2 to 5
Int vlan 2
Ip add 192.168.1.1 24
Qui
Aaa
Loc huawei pa s huawei
Loc huawei le 3
Loc huawei se tel
Then pass through the VLAN.