Adobe audition How to record

A lot of people on the network use Cooledit pro2.0 or 2.1 version of this is Adobe audition, it seems that the upgrade version, but it is really better than cool, personal feeling in the recording of sampling and noise reduction in the two processes than cool effect a little bit more real , the distortion relative to cool is not obvious (just personal feeling).

The following picture everyone slowly look, should be able to understand the entire recording process of it ~ I speak well in detail

Insert Accompaniment

Refresh effects List

Explain:

The right side is the total level of output, if your voice is too loud, turn it down a little bit, and vice versa. Left two high, low frequency ratio is very important, if your own voice recorded out of the stifleness, the low-frequency turn smaller, high-frequency push larger. Vice versa.

Explain one:

Predelay is early reflection, this should not adjust too much, try not to exceed 80ms, or it sounds like 2 people are singing.

Room size is naturally the size of the room, the larger the room, the more natural echoes, according to different songs, there will be different data. For example lyric some songs, relative echo to some more, size on the adjustment larger, about 75-90. If it is r&b, naturally not too big, 50-70 good.

EXPLANATION Two:

The most important thing here is decay time, I do not think more than 1s, otherwise the echo is too big, the effect will be too, the general control in between 0.6-0.9 is good.

EXPLANATION Three:

The Dry is the dry sound, the E.R is the wet sound, adjusts the wet and dry proportion is most important. The wet sound is not too big, otherwise the sound will come out some stifleness, compare the distortion.

Reverb is the most important reverb, this also avoid too large, pole probably in the middle of the position on the right side of the good.

In the end, all of them are finished, congratulations you also have their own works Oh ~ ~

1, noise reduction: the human voice before there will be a sound, that is ambient noise, select the ambient noise, then select "Effect" on the menu bar, then select "Refresh Effect List", the dialog box appears, select "Yes" after the refresh, then select the menu bar "effect" in the "noise elimination" option, however Select "Noise Filter" and press "close" when you go in. Again select the "Effect" in the menu bar "noise elimination" of "Denoising", and finally press OK, so the recording process of the ambient noise is eliminated. This is only the elimination of environmental noise, the end of the voice of the stems ending this also want to eliminate, otherwise it will affect the effect of the entire song to eliminate this noise has a special plug-in "waves" "Rvox" effect, this effect can be cut off the end of the voice of the stems ending, recommended settings do not, Otherwise, at the beginning and end of each sentence there will be a clear feeling of sudden disappearance of sound.

2, inspire the human voice: double-click People's sound track switch to the waveform editing interface, select all waveforms, and then in the "effect" in the "DirectX" in the "Bbesonicmaximizer" plug-in, and then we will see three knobs, the first tune is the bass, the second is the treble, The third tune is the total output volume. We can according to the voice to adjust the high and low tone and the total volume, began to record the human voice is not very strong, this need to raise the tone of the excitation, so that sounds good, do not believe you can try it.

3, Pressure limit: Install Waves 4.0, in the "DirectX" select "WavesC4", the adjustment window appears. At this time, according to their own voice to the high and low frequency adjustment, start to use the software may not know how to adjust the relevant data, you can do so, in the adjustment window to select "Load", you will see a lot of effects, you can choose the penultimate fourth "pop vocal", and then click OK. The function of the pressure limit is the high frequency of the human voice do not "noise", low-frequency do not "muddy". Start do not know how to use the above methods, after the proficiency of the following to adjust the correct data according to their own voice.

4, enhance the intensity and expressiveness of the human voice: the installation of "Ultrafunk FX" effect will have the name "compressor R3" effect, this effect is to enhance the intensity of the human voice and expression will be seen above the four small boxes, different data will have different effects, You can put these four data in when you don't know how to use them at first, the first input:-20 The second input: 4.0 The third input: 16 The Fourth input: 7.0 In addition to the top of the four, there are 2 below, the first input: 40 The second input: 200 then you can increase the intensity and performance of the human voice by confirming Force. The above provides only the approximate data, the concrete data also relies on everybody to feel, finally determines.

5, reverberation: The installation of "Ultrafunk FX" effect device will be called "Reverb R3" effect. This work needs to be very careful, different recording environment, different styles of reverberation effect are not the same. This requires constant accumulation of experience, large volume, sound absorption of the room, the effect of artificial reverberation time to be short. The reverberation time of male singers should be shorter; the reverberation time can be longer when the female sings. Professional singers should be shorter reverberation time, otherwise it will destroy the original timbre characteristics, amateur singers can be longer reverberation time to cover up the shortcomings of the voice and so on ... Start using this software friends can be specific to my data input, a total of 13 small boxes, first: 0.0 second: 145 Third: 4.5 Fourth: 160 Fifth: 100 Sixth: 100 Seventh: 2.6 Eighth: 116 Nineth: 1.6 Tenth: 1.2 The following three Press the default value. Again, the above is not the standard data, this is only for the first time to use this software friends, the specific data to rely on their own ears to feel.

6, Balanced human voice: Install the "Ultrafunk FX" effect device will be called "Equalizer" effect. The main role is to balance the human voice, so that high-frequency in keeping the premise of noise adjustment to clear and transparent, low frequency to ensure that the premise of the adjustment to clear, natural. Also start using this software friends can first use the data I provided, not the standard data, the specific data to rely on everyone to explore their own later. There are three columns of data in the effect, so I'll write out a list of them. First column: 40;60;200;800;4600;15000. Second column: 1.0;0.8;0.8;0.6;0.6;0.5 third column: 0.4;-2.2;0.3;0.0;6.5;0.0;0.0. Enter the data and press OK.

7, Mono Acoustic Stereo: The general record of the human voice are single way, this time need to replace the stereo so that sound will have a sense of three-dimensional and azimuth oh. The specific method is this: Double-click the track into the monorail mode, then press F11, then select the 16-bit stereo format, and finally press OK. Then select all waveforms, and then select the "Ultrafunk FX" effect called "Phase" effect. There will be three small box, the first is the sound phase state, the second is to tune the width of the sound field, the third is the volume size after processing. We put on listening headphones carefully listen to, tune to their own feeling the best data, and then press OK. This mono is converted into stereo, we listen to, is it better than mono? The first seven steps are the most basic human voice post-processing steps. There are many effects, this requires a lot of people to grope, a lot to try, and then add the effect to the human voice.

1, mixed shrink: The human voice post-processing after finishing and then is mixed up oh. Before mixing, the accompaniment should be dealt with, most of the accompaniment should be online download accompaniment, many accompaniment of the effect is not particularly good mixed before the first listen to the accompaniment, a little treatment, coupled with some low-frequency, pick good EQ. After the accompaniment processing, it will enter multiple track interface, adjust the volume of people's voice, if the singer sound good, May appropriately reduce some accompaniment music the weight, in order to highlight the singer's singing; If the singer is not familiar with the melody of the song, easy to sing out of tune, not close to the racket, in order to cover up these shortcomings, then appropriate to increase the volume of some accompaniment music. When the sound is adjusted, select "Shrink to an empty track (track 3)" In the Edit menu bar, then select "All waveforms". So the blending is done.

2, mixed shrinkage after the processing: after the contraction of a double click on the mixed track, into the monorail form, listen to the whole carefully, listen to whether the balance, whether need to add some low-frequency and so on, the EQ tune. A little bit of adjustment, adjust to their satisfaction so far oh. Everything has been adjusted, then to do is to save their work, double-click the mixed track, and then select the menu bar file, choose another save, choose a good file format, generally selected are MP3, according to determine.