650) this.width=650; "src=" http://s3.51cto.com/wyfs02/M02/73/8E/wKioL1YBBvzxSqTlAAQOhP2S3Rg500.jpg "title=" 1.jpg " alt= "Wkiol1ybbvzxsqtlaaqohp2s3rg500.jpg"/>
, perform a simple get-started experiment on Cisco devices and complete network interoperability
Recommended steps:
1. Configure the PC's IP address and gateway first
2. Activate the corresponding interface of the switch (the Cisco emulator is turned on automatically, it is not activated here)
3. Add IP addresses and static routes for routers
Operation Start:
Step one: Double-click on the PC2 machine on the graph to enter the configuration interface
650) this.width=650; "src=" http://s3.51cto.com/wyfs02/M02/73/8E/wKioL1YBCNTDHnHZAAL9WG_DdTc496.jpg "title=" 2.jpg " alt= "Wkiol1ybcntdhnhzaal9wg_ddtc496.jpg"/>
After entering, configure
650) this.width=650; "src=" http://s3.51cto.com/wyfs02/M02/73/91/wKiom1YBCcygk7CkAAWWvnB-kjs757.jpg "title=" 3.jpg " alt= "Wkiom1ybccygk7ckaawwvnb-kjs757.jpg"/>
The same configuration for the remaining 5 PCs is not explained here, as is the case with PC2, except that the IP and gateway are different
Step Two: Configure the switch, this experiment does not need to configure
650) this.width=650; "src=" http://s3.51cto.com/wyfs02/M00/73/8F/wKioL1YBDg_w1Gg6AAMC-VlH-BA152.jpg "title=" 4.jpg " alt= "Wkiol1ybdg_w1gg6aamc-vlh-ba152.jpg"/>
Step Three: Configure the router, double-click the router icon, as the switch into the third menu, enter the configuration interface, and then configure
(note, before the operation, open the Cisco Emulator menu bar, find options, click to select the first item, in the fifth line tick, display device connection number,)
650) this.width=650; "src=" http://s3.51cto.com/wyfs02/M00/73/8F/wKioL1YBEH7BEgzwAAK8d07rBuk083.jpg "title=" 5.jpg " alt= "Wkiol1ybeh7begzwaak8d07rbuk083.jpg"/>
650) this.width=650; "src=" http://s3.51cto.com/wyfs02/M02/73/92/wKiom1YBFdfy0ASTAAQOl_5S9sQ422.jpg "title=" 5.jpg " alt= "Wkiom1ybfdfy0astaaqol_5s9sq422.jpg"/> Display the connection number, you can configure the router, double-click the router you want to configure, select the command line
650) this.width=650; "src=" http://s3.51cto.com/wyfs02/M00/73/92/wKiom1YBGZ3zPyzAAAMYDvlpsjY028.jpg "title=" 7.jpg " alt= "Wkiom1ybgz3zpyzaaamydvlpsjy028.jpg"/>
Here is an explanation of the parameters of the static routing configuration (for example, the IP address configured in the real world)
IP route for the configured command
192.168.2.0 is the next network segment to reach
255.255.255.0 is the subnet mask of this segment to reach
10.0.0.2 is the router interface required to reach the next network segment
The second router does not explain here, with the first empathy
Verify that you can ping through the
650) this.width=650; "src=" http://s3.51cto.com/wyfs02/M02/73/90/wKioL1YBHnCzVabJAAKtnefjEoc074.jpg "title=" 8.jpg " alt= "Wkiol1ybhnczvabjaaktnefjeoc074.jpg"/>
650) this.width=650; "src=" http://s3.51cto.com/wyfs02/M02/73/90/wKioL1YBHymwejpBAAKUAVgaazQ345.jpg "title=" 9.jpg " alt= "Wkiol1ybhymwejpbaakuavgaazq345.jpg"/>
End of Experiment ~ Thank you for your support OH
Cisco emulator Simple Network connection operation