Hair color and background color similar how to pull a picture

hair color and background color similar how to pull the map | Pull map Skills | Photo Gallery post-production Training visits: 3580 News Author: Zhengzhou Late digital Training news Source: Zhengzhou Photographic Make-up Training School release time: 2010-11-2 9:34:39

Hair color and background color similar how to pull the map | Pull map Skills | Photo Studio later production training 1 use PS to open a picture of the material, this figure on the internet claiming the most difficult to pull the map. Today, I thought of a way to write it down and tell you. It should be the quicker way. 2) Copy background layer 3 Press ctrl+shift+u key, go color, we observed that the picture of the upper right corner of the background is relatively dirty. This place needs to be dealt with first, otherwise the figure that is pulled out behind will also be more dirty. (If the picture has a clean background, you don't have to do this.) This step is for the picture of the drawing preparation work, we perform the menu selection-> Color Range command. 4 at this time in the pop-up window we will find the top right corner, (Color range window is the brightest part of the selection, that is, White is the selection, black is not a selection) tolerance value can enlarge or narrow the section of the selection and the non-selection. To better dispose of the dirty upper-right corner, I'm going to set the tolerance value to 55 here, and note that this value is based on a different picture and uses a different value. The standard of regulation is to change the part we need to the white part as much as possible. The white part is the selection. 5 Click "Good", there will be a lot of ant line, hehe, but we only need the upper right corner of the part is enough, how to do it. I personally think that the faster way is to use the Lasso tool, then click the "Subtract from constituency" option and circle the unwanted ant line with the Lasso tool, and you'll find that the ants are gone, and the ant line in the upper right corner is still flashing. As shown in figure: 6 Press Ctrl+alt+d key, feather 10 pixels around, in order to transition nature; then press ctrl+m key, execute Curve command, set as figure, turn up some curves, let it cover the dirty part. When you are done, press Ctrl+d to cancel the selection, as shown in figure: 7 Well, the previous work has been completed, this, transfer into a picture you think you can do the background, and then renamed "Landscape", and then the "landscape" layer to the "1" layer below, while activating the "1" layer, as shown: 8 We change the "1" layer layer blending mode to "strong light" (strong light mode is simple to understand the neutral gray part of the transparent, other unchanged) This is what we have a lot of work before the preparation. Results as shown 9 If you feel that the hair is not clear enough, copy one, the method is to press Ctrl+j key, hehe, feel too strong, it does not matter, lower this layer of opacity, on the line. As shown in figure: 10) or the old way, the background layer to copy, and the new layer on top layer, and then under the layers panel press the Add Layer Mask button, as shown: 11) Press the D key, restore the default foreground/background color [black/white], and then click b to switch to the brush tool (not the Eraser tool, as the following will work on the mask, with the brush more convenient) and then smear the unwanted parts, leaving only the character part visible. As shown in figure: 12 originally if the MM is black hair, to this step is almost over, but this is the MM is yellow hair, alas, in order to achieve better results, there is no way to use the history of the Brush tool bar, lower some opacity and flow, enlarge the picture, some of the more coarse hair to restore some yellow bar, That would seem to be the case, don't you think? So I do, first create an empty layer, and then press Ctrl+alt+shift+e key, the printed cover visible layer command, very little use it, hehe. This will not destroy our masks (reserve the right to modify later), click the y key, switch to the history brush tool, reduce the opacity and flow, and slowly apply those coarse broken hair bar. As shown in figure: 13 to a simulation of the environment color bar, after all, the background is cold, the original picture is warm, click on the layer below the layers panel to add Fill Adjustment button, select Photo Filter items, as shown: 14 Use the Blur tool, smear some broken hair, let its sawtooth feeling disappear, the final result: