The latest HP X86 server is the GEN8 series, which uses the ACU tool to create RAID, which is a graphical interface that can be said to be friendlier.
Originally usually if is to buy a new server, standard two hard disk, then the default is done Raid1, but there are accidents, due to the large amount of PC server, a lot of this situation, you need to manually configure the raid, here use my photo to explain.
PC server is not the same as the general PC, if not raid, the server is unable to recognize the hard disk, so we installed the operating system in bulk, reported the following error (there is no physical disks attached-you will need to attach A supported drive to continue) is not raid, then raid, then install the operating system.
Well, not much nonsense, look at the picture to talk.
The following is the use of F10 boot to install the operating system, the report cannot find the available physical disk, unable to continue to install the operating system, so first raid, so that the server can recognize the hard disk.
650) this.width=650; "src=" http://s3.51cto.com/wyfs02/M01/58/E6/wKioL1TAdaLgOghiAAFE-6kADu0106.jpg "style=" float: none; "title=" 2015-01-22_114827.png "alt=" Wkiol1tadalgoghiaafe-6kadu0106.jpg "/>
We restart the server, in the proceed to such as interface, press F5 to go to the ACU configuration view
650) this.width=650; "src=" http://s3.51cto.com/wyfs02/M00/58/E8/wKiom1TAdNGj5SyGAAPpOkZEogM295.jpg "style=" float: none; "title=" 2015-01-22_115200.png "alt=" Wkiom1tadngj5sygaappokzeogm295.jpg "/>
This is a F5 picture.
650) this.width=650; "src=" http://s3.51cto.com/wyfs02/M01/58/E9/wKiom1TAdNrhGJklAAVJN1rQXmk333.jpg "style=" float: none; "title=" 2015-01-22_115218.png "alt=" Wkiom1tadnrhgjklaavjn1rqxmk333.jpg "/>
After waiting a few minutes, go to the ACU interface, we do not see any available RAID information, can confirm the raid is not configured
650) this.width=650; "src=" http://s3.51cto.com/wyfs02/M02/58/E6/wKioL1TAdbeyF2vZAARXDPlWDqo673.jpg "style=" float: none; "title=" 2015-01-22_115232.png "alt=" Wkiol1tadbeyf2vzaarxdplwdqo673.jpg "/>
Here is a warning message, let's take a look at the "Dynamic Smart Array b120i RAID" array card under "Array Controller"
650) this.width=650; "src=" http://s3.51cto.com/wyfs02/M01/58/E6/wKioL1TAdbqQtTUnAAH26_1yN_A318.jpg "style=" float: none; "title=" 2015-01-22_115244.png "alt=" Wkiol1tadbqqttunaah26_1yn_a318.jpg "/>
Look at the "warning" on the right, the array card support write cache, but we did not create the array, nor used, so the warning, so here can be ignored
650) this.width=650; "src=" http://s3.51cto.com/wyfs02/M02/58/E9/wKiom1TAdOfRE9mvAAIkyaQ_Juo590.jpg "style=" float: none; "title=" 2015-01-22_115309.png "alt=" Wkiom1tadofre9mvaaikyaq_juo590.jpg "/>
OK, start configuring the array, select the "Dynamic Smart Array b120i RAID" array card under "Array Controller", click the "Configure" option
650) this.width=650; "src=" http://s3.51cto.com/wyfs02/M00/58/E6/wKioL1TAdcPg8pZtAAL-EdiAWL8844.jpg "style=" float: none; "title=" 2015-01-22_115325.png "alt=" Wkiol1tadcpg8pztaal-ediawl8844.jpg "/>
Then in the middle of the new window, select "Create array" to start creating the array
650) this.width=650; "src=" http://s3.51cto.com/wyfs02/M00/58/E9/wKiom1TAdPKzM3ylAAO2J7rjDlU484.jpg "style=" float: none; "title=" 2015-01-22_115340.png "alt=" Wkiom1tadpkzm3ylaao2j7rjdlu484.jpg "/>
Here are the two hard drives on my server, tick the checkbox in front of "Select All"
650) this.width=650; "src=" http://s3.51cto.com/wyfs02/M01/58/E9/wKiom1TAdPWTQLmSAAI7izSyLlw092.jpg "style=" float: none; "title=" 2015-01-22_115350.png "alt=" Wkiom1tadpwtqlmsaai7izsyllw092.jpg "/>
When selected, displays
650) this.width=650; "src=" http://s3.51cto.com/wyfs02/M01/58/E6/wKioL1TAdc7AA0zqAAGZpTV-a14644.jpg "style=" float: none; "title=" 2015-01-22_115402.png "alt=" Wkiol1tadc7aa0zqaagzptv-a14644.jpg "/>
We do RAID1, other according to their own needs to choose, I have no need here, all default, Next
650) this.width=650; "src=" http://s3.51cto.com/wyfs02/M02/58/E6/wKioL1TAddGDp8oiAAIEzjbTz-M396.jpg "style=" float: none; "title=" 2015-01-22_115413.png "alt=" Wkiol1taddgdp8oiaaiezjbtz-m396.jpg "/>
Here is the summary information, if confirmed, click "Finish" to complete
650) this.width=650; "src=" http://s3.51cto.com/wyfs02/M02/58/E6/wKioL1TAddPyQxJTAAGS7HexVJA838.jpg "style=" float: none; "title=" 2015-01-22_115421.png "alt=" Wkiol1taddpyqxjtaags7hexvja838.jpg "/>
Back to the beginning of the interface, but under the array card already has the array information, indicating that at this time RAID1 has been created OK, but also can be recognized by the server.
650) this.width=650; "src=" http://s3.51cto.com/wyfs02/M02/58/E9/wKiom1TAdQKjolqAAAQEkRRVRl0111.jpg "style=" float: none; "title=" 2015-01-22_115442.png "alt=" Wkiom1tadqkjolqaaaqekrrvrl0111.jpg "/>
Click "Arrays" to see if you have a logical disk after RAID1, and you can see the local two 500G local disk.
650) this.width=650; "src=" http://s3.51cto.com/wyfs02/M00/58/E6/wKioL1TAddvCfKhxAAGEz7r-9fA621.jpg "style=" float: none; "title=" 2015-01-22_115450.png "alt=" Wkiol1taddvcfkhxaagez7r-9fa621.jpg "/>
Now that the disk array raid has been created, reboot and use F10 to start booting the operating system.
This article is from the "Heavenly Soul Eternal" blog, please be sure to keep this source http://tianhunyongheng.blog.51cto.com/1446947/1606948
HP GEN8 Server Create RAID (there is no physical disks attached)