To give you illustrator software users to detailed analysis to share a mouse painting to create a beautiful texture robot production tutorials.
First, create a new document
1. Select the Ellipse tool and draw the ellipse on the canvas.
2, using the direct selection tool (white arrow), the ellipse to adjust the following figure. Drag the topmost node of the ellipse to the middle position (around 3/2) to lengthen this node handle.
3, choose to adjust the handle of the left and right nodes, the lower part of the ellipse into the next half, as shown:
4. Use the same method to draw the head of the robot. As shown in figure:
5, select the tool (black Arrow), (2) point position drag out the selection box, the robot's head and body all box selection, release the mouse.
Sets the fill color to white, the stroke color to 30% grayscale, and stroke to 2PT. If your color mode is CMYK, you can change the color mode by opening the triangle button in the upper-right corner of the color panel.
6, use the selection tool (black arrow) to select the head of the robot, hold down the ALT key while dragging the mouse, so that this object can be copied.
Keep the avatar copied to the selected state, set the fill color to white, and stroke to none. Adjust the location of the copied object, using the top and bottom keys on the keyboard to adjust and move two pixels to the right. Use the same method to draw the body parts of the robot. As shown in figure:
7, select the cloned robot body object, using the Grid tool, add the following figure shown in the grid. In this step, the use of the grid is relatively simple, as long as the attention in the use of grid, point on the sideline on the line.
After you add the grid path, use the direct selection tool (white arrow) to select the nodes on the grid to add color. Be aware that the two-end color of a network is consistent.
The color reference values in the following order are: 2 point 43%; 3 o'clock 23%; 4 O'Clock 13%; 5 O'Clock 0%; 6 o'clock 20%. are grayscale.
8. Use the Pen tool to draw a color block at the upper end of the body, as shown. Set gradient, type: radial. Two color standard reference values are: 0 and 45.
9, use the Pen tool again to draw a path, filled with no, stroke is white.
10. Use the same method to add a mesh to the head of the robot.
11, the head of the object 1, 2, 3 points at the edge of the 30% gray level. Note that the right side of the surface is left white.
All points in the path on the 7 point are white. 62 at 15% 5, 4 for 20%
Everyone can paint according to their actual situation.
In this step, we should pay attention to the control of the grid path, the length and direction of the handle directly control the proportion of color and how much.
12, the completion of the final results are as follows:
13, the use of elliptical tools, draw a black oval, stroke without. Use the direct selection tool to adjust. And then fill in the 100-65% gradient. As shown in figure:
Second, the production of robot accessories
1. Use Pen tool, draw arm shape, fill 100-14% gradient. As shown in figure:
2, keep the object selected state, select Object-Path-offset path, displacement 2PT.
3, set the gradient to 45-10%. Change transparency as needed.
4, use the Pen tool to draw the left arm path, fill black, stroke without.
5, pull an ellipse above the left arm, set a 100-14% radial gradient, use the gradient tool, drag in the object, you can change the gradient angle and size. Adjust to the following effect:
6. Hold down the SHIFT key and select the object on the Layers panel. (A blue box appears at the rear of the layer to indicate that it is selected)
7, open the Opacity panel, click on the upper right triangle, choose to create an opacity mask.
8, the completion of the effect. (You can change the opacity as needed.) The right hand is grouped and moved to the bottom of the object.
9, using the elliptical tool to the left hand, with the direct selection tool to adjust, set the fill to white, stroke of 30% Gray. The following figure:
10, Keep left selected state, object-path-offset path, displacement -2pt. Fills the copied object with white, and the stroke is set to none.
11, use the Grid tool to increase the network path. As shown in the figure.
12, fill color. From left to right. 0%,10%,15%,0%,10%,5%,25%,5%.
13, 2 points set at 5%,3.4.5 Point set 0%. Then adjust the grid, as shown in the diagram.
14, the above is a way to add a mesh, many beginners will because the addition of grid, grid line is not good control. Here's a quick way to introduce a simple point.
You can draw an ellipse first, set two basic gridlines, and then drag the object with the mesh to the left hand shape, and then add the detail grid line. In this way, you will find that the grid line becomes very well controlled.
15, select the rectangular grid tool in the Line tool group, such as 1. Draws an object such as 2. Set blue fill black padding. Change the stroke to 0.1pt.
When the drawing is complete, drag the rectangular grid object to the Pattern panel.
16, the use of elliptical tools to draw the eyes of the robot, in the object is kept selected in the state, with a pattern to fill.
Third, highlight drawing and shading.
1, the head and body parts on the machine, each draw a small white dot, no strokes.
Menu effect Blur Gaussian blur, set 2 pixels in the dialog box.
2, finally using the Ellipse tool to draw the projection.
Well, the above information is small weave for you illustrator of this software users brought the detailed mouse painting to create a beautiful texture of the robot's production tutorials to analyze the entire content of sharing, you see the users here, small knitting believe that everyone is now very clear the method of making it, Then everyone will go to follow the small part of the tutorial on the sharing of their own to try it.
