Four ways to finish printing ink-jet printer

Inkjet Printer Surface treatment methods are diverse and new technology new materials, but the current ink-jet printer surface treatment is commonly used in the main way to film, plastic seal, cold mounted, film covering such four kinds of methods mostly.

1, leaching film

The film is a special liquid evenly smear on the printed paper surface and then through the curing of a treatment mode, by a specialized laminating machine for operation, film characteristics are:

A, good quality coating adhesion fastness, not foaming, good sealing performance, the surface as a mirror.

B, the cost of printing paper surface processing cost is the cheapest, or even less than one yuan per square meter material.

C, simple to operate after the film does not have any late work, will not leave any side strips, no cutting work, a lot of labor, is the bulk of the production of the preferred equipment.

D, high prices also require specialized site laminating machine is divided into many types, but are expensive equipment, large size occupies a place, the need to set up a separate operating site.

2. Cold Mounted

Cold mounting is a kind of adhesive tape on the back of the printed surface of the paper after a treatment, generally with the help of cold laminating machine to complete. Its characteristics are:

A, fast speed of the printing paper surface processing speed of the fastest way.

B, the adaptability of strong printed paper, whether wide, narrow, long, short, all of them.

C, can provide a variety of surface effects of cold laminating film species rich and diverse, in addition to the high light and Matt of the points, there are also what scrub, laser, powder and so on, can make the processing of the paper surface more diversified.

D, simple and inexpensive equipment, cold laminating machine cheap, in use also not electricity.

E, the quality is generally adhesive after all, so the quality of cold mounted generally. In particular, if the cold mounted after the paper is curled and then expanded may appear bubbles and folds. Single-sided cold mounting also makes paper curl easily.

F, easy aging, there is a contraction, should not be long-term preservation and do not say that the quality of the film itself, even if the quality of the current market is relatively good cold laminating film is also prone to aging, shrinkage problems, is not conducive to long-term preservation, so want to keep the long-term photos remember not to use the cold mounted way.

3. Plastic Seal

Plastic seal is a double layer of software film will be printed in the middle of the paper, and then through the plastic sealing machine to glue the film around, forming a paper sealed in one of the treatment. Plastic seal has the following characteristics:

A, simple and cheap equipment at present more in the A3 format, the price is cheap.

B, simple operation only a few switches and a temperature knob, the operation is very simple.

C, a machine more plastic sealing machine in addition to plastic and can be used for cold mounting or even do without laminating cards and peritoneum.

D, plastic seal after the photo is very plastic after the film becomes hard and brittle so that it can not curl, the work forms a rigid board, so that in such as the chest card, tag and other production play a role in the small photo gallery is often used in the post-processing of a major method.

E, the quality is generally limited by plastic sealing film, plastic seal of the general quality. Plastic sealing film through heating and paper surface adhesion but not close, that is, plastic sealing film and paper can not be fully pasted together, a certain time after the plastic bag can enter the air, so the plastic seal of the decorative and protective role is generally.

F, easy aging plastic sealing film through heating hardening, can not fold can not curl so not suitable for large-face, plastic seal film is also subject to temperature changes, too cold brittle.

4, Hot film

The plastic covering can be understood as the late processing technology of the paper-plastic integration, including laminating and cold mounting. In the narrow sense of the film refers to the thermal laminating machine.

The thermal laminating machine can be divided into two categories, namely, coated laminating machine and pre-coated laminating machine. That is, coated laminating machine including glue, drying, hot pressing three parts, its wide range of applications, stable and reliable processing performance, is currently widely used in the domestic coating equipment. That is, the coating laminating machine is mainly used for the continuous production of large quantities of factory, and the volume of the machine is very large. Pre-coated laminating machine without glue and dry parts, small size, low cost, flexible operation, not only applicable to large batches of printed film laminating processing, but also applicable to automated desktop Office systems, such as small batches, scattered printed film laminating processing, small machine size, can be placed on the desktop to use, Pre-coated laminating machine can be carried out in addition to the peritoneum can also be carried out by the cold table, this article is referred to as the following is the use of film-coated laminating machine.

This kind of thermal laminating machine uses a membrane with a coating of a similar hot sol, which is completely combined with the surface of the paper through high temperature and pressure, and the membrane used is called hot film and the equipment used is called the Hot film Machine or the hot laminating machine. Hot film machine can also be used for cold mounting, so also known as laminating machine. Hot film generally double-sided, that is, the front and back of the paper should be covered with film, but the film is coated when the front and back is a complete.

The difference between the thermal film and the plastic seal is mainly the film, the plastic seal is mainly sealed around the edge, membrane and paper surface is not completely paste, rely on is sealed, so the plastic seal film is a single double layer of the form, to the paper folder in the middle of the double layer of plastic seal, the film is thinner and more soft, rely on the paper with the surface of the intimate combination, Packaged in the form of a roll pack. The characteristics of the hot film are mainly embodied in:

A, the quality of the membrane is fully integrated with the paper, there is no air entry, but also the double-sided coating so that the paper will not be due to the contraction of the membrane deformation, the basic elimination of wrinkles, bubbles, shedding and other phenomena so that the film covering the quality appears better.

B, low cost even if the double-sided film is also more than one side of the cost of the cold mounting is also cheaper, the hot film after the paper is not like plastic seal after that hair hard, paper or have softness, can curl.

C, can provide a variety of surface effects to increase the beauty of the hot film in addition to a calendering film, high light film, and some surface with special effects of a variety of pattern film, increase the appearance of the hot film.

D, the use of more extensive after the film due to both sides of the paper has a layer of film, paper has a better flexibility, corner more difficult to be torn, for catalogs, such as books, recipes, such as the need to often turn over to see is the best mulch treatment mode

E, the operation of simple scrap rate of low heat film machine has a pause, thermostat, speed and other functions, easy to operate, but also the use of roll-coating film, continuous operation, high production efficiency, film-coated scrap rate is low.

F, Retroperitoneal treatment appears to be troublesome after laminating the paper will leave excess heat film need manual removal, heavy workload and appear troublesome.

G, not suitable for the operation of the hot film machine to start and close the time is slow, if only a few or a small amount of film covering too much delay, because the thermal film machine to start about 20 minutes or more preheating, cooling before the shutdown also takes time.