When using a wireless router, three passwords are involved: wireless password, router management password, and broadband password. The role of each password is shown in the following figure:
The following describes how to set or modify a password.
1. I want to change the wireless (WiFi) password
The wireless password is the password required for wireless terminals (mobile phones and laptops) to connect to wireless signals. The wireless router does not have a wireless password for the wireless signal in the default factory status. The method for changing the wireless password is as follows:
1
, Logon Management Interface
Open your browser, clear the address bar, enter tplogin.cn (some routers are 192.168.1.1), and enter the management password in the pop-up prompt box, as shown in the figure below:
Note:: The Management password is set by the user. If you forget the password, restore the factory settings of the router and then reset it.
2
Set a wireless password
After entering the management interface, modify the wireless password on the right side of the interface, and click
SaveThe new wireless password takes effect immediately.
Note:: The password length is 8 ~ 63 digits. A combination of numbers or letters is recommended.
For some earlier vrouters
Wireless Settings
>
Wireless security settingsInterface settings or modifications
PKS
Password, Click
Save. Some routers need to be restarted before the settings take effect. Follow the prompts on the page.
Note:If you only change the password without changing the Wireless name, terminals that have previously connected to the signal must delete the wireless configuration file before they can connect to the signal normally.
2. I want to change the vro management password
The management password is the password you need to enter when logging on to the vro management interface.
Modification method: Log on to the vro interface and click
Route settings
>
Change administrator password, Enter the original logon password, set the new management password, and click
Save, As shown in the following figure:
Some vrouters
System Tools
>
Change logon passwordInterface modification. After setting is completed according to the page prompt, click
Save.
3. I want to change the Internet bandwidth password
The broadband password is the password for broadband dial-up Internet access. It is provided by the broadband carrier (China Telecom, China Unicom, and so on). You can only enter your broadband password in the vro.
Setting method: Log on to the vro interface and click
Route settings
>
Internet settings, Select the Internet access method
Broadband dial-up Internet access, Input
Broadband accountAnd
Broadband password, Click
ConnectionWait until the IP address is obtained successfully.
You may be concerned about the following issues:
After changing the wireless password, why can't I connect to the wireless device?
After changing the wireless password, you need to delete the wireless configuration file stored on the terminal and try again.
Refer to the operation method of the corresponding Operating system:
To delete a configuration file in Windows XP, follow these steps:
Find on the desktop
Network neighbors,
Right-clickSelect
Attribute. Find
Wireless network connection,
Right-clickClick
Attribute, As shown in the following figure:
Find and click
Wireless network configuration, In
Preferred NetworkClick
Delete, And
OK. As shown in the following figure:
To delete a configuration file in a Windows 7 operating system, follow these steps:
Click the wireless network icon in the lower right corner of the computer, and click
Open Network and Sharing Center, Find and click
Manage wireless networks, As shown in the following figure:
Find the wireless signal to be deleted, right-click
Delete a network, As shown in the following figure:
To delete a configuration file in Windows 8, follow these steps:
Click the wireless signal network icon in the lower-right corner of the computer. In the displayed network list, find the wireless signal to be deleted,
Right-click
Select and click
Forget this network, As shown in the following figure:
To delete a configuration file in a Windows 10 operating system, follow these steps:
Click the wireless network icon in the lower-right corner of the desktop.
Network Settings, As shown in the following figure:
Find and click
WLAN, Click
Management
Wi-Fi
Set, As shown in the following figure:
In
Management
Wi-Fi
SetPage, find the following
Manage known networksAnd click
ForgotAs shown in the following figure:
To delete a configuration file in a Mac OS, follow these steps:
Enter
Mac OSAfter the system
DockFind and click
System Preference settings. In
System Preference settingsInterface, click and open
NetworkInterface, Select
Wi-Fi, Click
Advanced, As shown in the following figure:
In the displayed dialog box, click
Wi-Fi, Select the wireless signal to be deleted, and click"
-", Then click
Good, As shown in the following figure.
The Android operating system deletes the configuration file as follows:
In
WLANThe setting page displays the wireless signals to be deleted. In the displayed dialog box, select
Cancel network saving. As shown in the following figure:
To delete a configuration file in iOS, follow these steps:
In
Wireless LAN (or
Wi-Fi
)Set menu, click
Blue exclamation pointAs shown in the following figure:
Click
Ignore this network, As shown in the following figure:
