How to install and debug a Home Router

Home Router installation and debugging often happen at home. There are many things involved in the installation of home routers. There are also a variety of backup technical methods, so there will be a bit of confusion in the selection of methods, the following shows you a way.

Home Router installation and debugging

I bought a vro to allow my laptop and desktop to access the Internet. However, after reading the instructions, I got confused for a while, as soon as you log on to the bandwidth, you will be prompted about things like "using WAN" and "PPPOE. Do you have any experts to help me buy a home router with four connection ports for installation? Is it difficult for me to set it or what is going on?

First, you need to know how to access the Internet. Some IP addresses are automatically obtained when you do not use a vro. You can run the ipconfig/all command at the command prompt to check the IP addresses, the original network cable connected to the computer is connected to the WAN port, and the computer is connected to the LAN port. Next, let's look at the specification. What is the default IP address of the router? Change the gateway to the default IP address of the router in the network neighbor attribute, the IP address of the computer uses another IP address in the same network segment. For example, if the default IP address of the router is 192.168.0.1, you can set the gateway to this IP address and set the IP address of your computer to 192.168.0.22 ~ Any number in 254 can be used, and the first three digits must be the same), subnet mask 255.255.255.0;

Then, read the instructions to log on to the Home Router Installation Management Interface. Generally, open the browser and enter http: // 192.168.0.1. On the logon interface, the username and password are mostly admin. After correct input, login successful; if your original IP address is not 192.168.0.N, the IP address of the router will not be changed. If the original IP address is in this network segment, change the IP address set on the LAN end to another IP address segment. For example, change 192.168.0.1 to 192.168.1.1. After saving the IP address, change the gateway on the computer to 192.168.1.1, change the IP address to 192.168.2.2, and then log on again. Set the IP address on the WAN end, you can select multiple methods. The method you used to access the Internet is selected here. After the method is selected, the corresponding parameters will be displayed. For example, if you used the dialing method, select the dialing method, enter the correct dialing account and password, and save the settings.

Next, let's take a look at the connection method. You can see if you want to modify it based on your needs. If it is an automatic connection, the connection may start. There is also a DHCP. If you enable it, the computer can automatically obtain the IP address, and the DNS can also be empty. If it is not enabled, you need to set the IP address, gateway, and DNS by yourself, if you do not know the DNS on the internet, set it to the IP address of the router, which is the same as that of the Gateway. The router is automatically forwarded to the Internet. As long as the router is connected normally, you can access the Internet.

Is the Home Router installed?

◆ Connect the broadband cat and the WLAN port of the router to the power cord.

◆ Confirm the connection, and then set the TCP/IP options for the PC: choose "start"> "Settings"> "network connection"> "Local Connection"> "right-click Properties"> "Internet Protocol (TCP/IP)" and click "Use the following IP Address, [IP Address: 192.168.0.2] or [IP Address: 192.168.1.2] (because the factory IP address of the Broadband Router is different, some are 192.168.0.1 and some are 192.168.1.1. For details, refer to the Manual) [subnet mask: 255.255.255.0 〗.

◆ [Default Gateway: 192.168.0.1] or [IP Address: 192.168.1.1] (because the IP address of the PC must be in the same CIDR block as the Broadband Router, refer to the IP address in the router Manual ). Then, click "Use the following DNS server address" and select "p" as the preferred DNS server and select "a" as the DNS server address. (You can set DNS based on your region because the region is different, if you do not know, click Start-run-Enter cmd-command ipconfig/all) to set it. -OK ].

◆ Log on to the vro and set double-click the desktop IE browser. in the address bar, enter the IP address of the 192.168.0.1 or 192.168.1.1 vro (refer to the IP address in the vro Manual ). Press the "enter" key. The vro setting interface is displayed. 1. Enter the user name and password. For more information, see the user name and password in the vro manual. Step 2. welcome interface of the router ,. click "Installation Wizard" Next Step 3 .. for Internet access, you can select your own broadband line, such as ADSL and ADSL. Next Step 4. login method, such as PPPoE dialing, select PPPoE, next step, 5. enter your ADSL user name and password provided by the carrier. Next Step 6. select the automatically assigned IP address and click OK.

◆ Set PC Internet sharing to open another machine, click Start> set> network connection> Local Connection> right-click Properties> double-click Internet Protocol (TCP/IP) ], and then click "IP Address: 192.168.0.3" or "IP Address: 192.168.1.3" (because some of the factory IP addresses of the Broadband Router are 192.168.0.1 and some are 192.168.1.1, for details, refer to the instruction manual) [subnet mask: 255.255.0] [Default Gateway: 192.168.0.1] or [IP Address: 192.168.1.1] DNS server settings, as above ②. -OK]★Green memories★Install the home router.