How to Set up a router to connect two computers

 

How to Set up a router to connect two computers

Use the broadband routing method. The benefit of this method is stability! There is also effort-saving. You don't need to dial every time you access the Internet. This is done automatically by the broadband route. In addition, the broadband route has the reconnection function, saving you a lot of trouble? The next step is security. The IP address that you expose to the Internet is the IP address of your route, not the IP address of the machine itself, so that you are virtually protected.

In addition, there is no violation of China Telecom or China Netcom regulations. Even if he limits the MAC address, it is useless because the route itself has a MAC address.

1. First, connect the broadband cat to the WLAN port of the router. You can use the random cable of the cat.

2. Use a direct connection network cable to connect a LAN port of the router to the upling port of the switch. You can also use a direct connection network cable to connect the common port of the switch to the computer. In this way, the hardware environment is ready. If you have fewer machines and there are two or three machines, there is no need to add a vswitch. You can connect a LAN port of the vro to a computer with a direct connection network cable.

3. Set your network parameters on the first machine (right-click "Network Neighbor"-"properties"-Right-click "Local Connection"-properties-find the TCP/IP protocol, and then double-click it) (sometimes you can set the obtained IP address to be freely obtained)

IP Address: 192.168.1.11

Subnet Mask: 255.255.255.0

Gateway: 192.168.1.1

DNS: Ignore it.

Then click "OK" to restart the instance. But are you sure you want to restart it.

4. The second machine, for example, the first server, is to change the IP address to 192.168.1.12. And so on. At this time, the LAN is successfully formed.

5. Set up a broadband route. I think there should be instructions. I just want to give a brief introduction.
First find a machine, then open IE, enter 192.168.1.1 in the address bar, and then press Enter. Prompt you to enter the user name and password, see the instruction manual.

After entering the routing configuration page correctly, you need to enter your Internet user name and password if you select pppoe for ADSL dialing. For direct IP Address Allocation, contact your ISP for details.

In Start> RUN> msconfig, Enter cmd. In the displayed window, enter ipconfig to check the gateway information returned? 192.168.0.1 and 192.168.1.1 are common D-link and TP-link addresses with a large volume of goods available on the market. Not all routers use these addresses, A vro like 3Com defines the IP address 192.168.2.1. A foreign-branded router or a vro with a cat uses 10.0.0.x as the IP address ....... After obtaining the vro address, it is much easier to set your IP address to the IP address of the same network segment and then access the IP address.

1. Connect the telephone line to ADSL cat, and connect the WAN port of the route from the cat's network cable
2. Connect the two computers to the LAN ports of the router respectively.
3. Set the IP addresses of the two machines to 192.168.1.2 and 192.168.1.3 respectively. The subnet mask is 255.255.255.0 and the gateway 192.168.1.1. You can enter 192.168.1.1 for DNS.
4. After setting the IP address, open IE with a computer. Enter 192.168.1.1 in the address to go to The vro setting page. the user name and password are admin.
5. After entering, you can use the setting Wizard to select pppoe for the Internet access mode, enter your ADSL account and password, and save the settings.

Possible problems:
Enter 192.168.1.1 in IE, or set a route where the user name and password are not admin, it may have been modified. In this case, you can reset the router to restore the default value. There is a small button behind the vro. Hold it down until the light of the route flashes, restart the route, and try again.

The IP address of the computer can actually be set to the range of 192.168.1.x 2 ~ 254 if you do not select the IP address as needed, it will be OK if you do not repeat it with the gateway IP address (that is, the IP address of the router, which is generally 1) or the broadcast IP address (generally 255.