How to set up Tp-link repeater with mobile phone

the method of setting up the mobile phone of Tp-link repeater

1, to set up WiFi wireless relay, you first need to ensure that the relayed wireless router is normal network, in order to facilitate understanding, we sometimes call the relay wireless router as a superior router or relay signal, and we want to set up a wireless relay router is called a relay wireless router or wireless repeater, to differentiate, Look, don't get mixed up.

Use the mobile phone or computer into the relay of the wireless router, the author of the Tp-link wireless router for example, into the Router Settings page to view the operation of the router, to ensure that the router has been networked, if the relay router is not networked, then wireless relay is also unable to access the Internet.

2, also should note that, because most manufacturers set the default IP address at the factory, it is necessary to ensure that the LAN port (LAN) IP address of the relay wireless router is not the same as the IP address of the relay wireless router to be set up, or it may cause an IP address conflict on the relay wireless router. If the relay wireless router is not handled properly, there may be networking problems (think of both routers with the same IP address, naturally do not know which router from the Internet to understand).

The best solution is to enter the "network parameters"-"LAN Port Settings", the first to be relayed to the wireless router's IP address, the general modification of the 4-bit digital IP address of the third can be. If it is not possible to modify the IP address of the relayed wireless router, it does not matter, but the wireless relay setting is slightly more cumbersome, as will be mentioned in the following.

3, to confirm the relay of the wireless router network after normal, into the "Wireless Settings"-"Basic settings", you can see the wireless router "SSID number", this is the wireless network we want to relay the name, and then set up after the relay will be used, note down.

In addition, it is necessary to note that the relay wireless signal can not use the "automatic" channel, some routers by default will be set to Automatic channel, which will cause the router to restart, repeaters due to different channels caused relay failure, it is recommended to set the Channel 1, 6, 11, and so on.

4, Next go to "Wireless Settings"-"Wireless security settings" to see the relay of the wireless signal security settings, pay attention to the password do not make a mistake oh.

5, so far, the relay of the wireless router to complete the preparation, and then start to set up the relay wireless router.

When you open a new wireless router's wrapper, you will typically have an installation guide that tells you how to connect to the wireless router, but the designer may not consider wireless relaying, so you'll need to figure it out for yourself. Taking the JCG wireless router as an example, the connection diagram does not explain the situation of wireless relay, but according to the experimental results, as long as the wireless router's wide area network (WAN Port) does not insert any network cable.

6, according to the wireless router connection diagram, in fact, there is no good connection, just plug in the router power can be.

After the router is started, the phone should be able to search the wireless router's signal. Do not know which signal to connect? Check the router's standard bar, the general wireless router will be marked on the label attached to the key information of the router, such as router IP address, network name, wireless password and so on.

7, open the mobile phone, into the "Settings"-"Wireless local Area Network" (here to the iphone as an example), you can see the factory default wireless network name, but do not worry about the connection. In order to facilitate users to access the Internet, smartphones generally have wireless network automatic switching function, therefore, before setting up a router relay, in order to avoid the setting of the mobile phone randomly switching wireless network caused by the failure of the problem, we need to be able to connect to the wireless network "Ignore" (Android phone needs to "cancel save").

8, open the wireless network signal on the right side of the small circle can "ignore the network." Note that all wireless networks you can connect to are "ignored" or "canceled".

9, now can be based on router stickers above the information to connect to the relay wireless router. Select the name of the wireless network on the label, enter the correct wireless password, and click "Join".

10, after joining the wireless network, the iphone will automatically detect the network status, for the set of JCG wireless router, the iphone will automatically login to the wireless router settings interface.

To prevent the iphone from detecting that wireless is not networked and automatically switching to other networks or 3g/4g data networks, we need to temporarily "cancel" the iphone's login function.

11, click the upper right corner of the "cancellation", iphone will show the Choice menu, do not hesitate to choose "Do not connect Internet use" bar, where you can rest assured that, even if the choice, does not affect the iphone's Internet function, but to tell the iphone the wireless network is not connected to the time, but also use him, Don't jump around to other networks.

12, the next step into the Router Settings page, if the iphone does not continue to stay on the Router Settings page, you may need to open the browser, in the Address bar to enter the router's IP address to enter the router settings page.

After entering the settings page, the router automatically prompts "The network cable is not plugged in!", well, it's smart. No, I'm right. (Note that the router's WAN port does not plug in the network cable OH), we choose "WiFi Wireless Relay" mode.

13, the router will automatically scan the surrounding wireless WiFi signal, waiting for the scan to complete, you can choose to relay the wireless network signal.