KMPlayer Filter Management mechanism

KMPlayer the custom filter manager without adding any separators. Haali check "Connect to MKV file" and "Connect to MP4 file". See Vc1remux let Haali "connect to Mpeg2ts", use up cancel tick.

Avi Selected Kmpavisourcefilter,mkv selected Gabestmatroskasource,wmv automatic selection.

Kmplayermpeg1,mpeg2ps,mpeg2ts selected Nero,nero,gabest respectively.

If you look at the demo, change the mpeg2ts separator to Nero.

If you look at 1080P High code H264, the MPEG2TS separator to elecard,cpu very strong on the use of Nero or haali,cpu is not enough to choose PDVD7.

Decoder aspect:

There should only be COREAVC and Sonicaudio two decoders in the custom filter manager, set to mandatory and not used. Look at the 1080P high code H264 to the former mandatory cancellation. Any film that contains a EAC3 track (Remux or Hdre) is "forced to use Soniccinemasteraudio" in the custom filter manager.

KMPlayer

The following is a detailed discussion, is the novice to learn the content: first long-winded paragraph: separation and decoding different. Separation is determined by the package format of the file, such as AVI,MKV,WMV,TS,TP. Ts,tp,wmv is the HD packaging format, the corresponding video encoding is (H264/MPEG2/WMV-HD), avi,mkv is the most hdre encapsulation format, the corresponding video encoding is (H264,xvid).

The efficiency of the separator itself is simple in the drag-and-drop speed, it and video audio decoder with good or bad problem, but the working effect and general/speed mode, covering/VMR renderer completely irrelevant. So when choosing a separator, do not consider the pattern and renderer.

First, AVI and MKV. First, make sure that Haali is not placed in the custom filter manager. In this way, AVI and MKV separators are only determined by two small hooks, and achieve optimal results. Avi and MKV are completely unaffected by the "preferred, 00800000, mandatory, set as source Filters" in the custom filter manager, and it is not possible to use Nero,elecard or PDVD7 separators.

kmplayer*. Avi:

The AVI separator is determined by the filter control "source Filter", with four selections at the bottom of the General tab for "normal Avi", the system default (Avisplitter), the Gabestavi separator (gabestavisplitter), and the Kmpavi source filter ( Kmpavisourcefilter), KMP internal AVI separator (kmpavireader). In parentheses is the name of the separator that can be seen when playing.

In addition, if you select the Connect AVI with Haali separator (if a Haali separator is installed) in the Other tab, you will definitely use Haali to detach avi If you disregard the settings in the General tab. As long as the "connect to a type of file" is turned on in the "Other" tab of the source filter, KMP will definitely detach the file with Haali. Setting the Haali to the source filter in the Custom filter manager is equivalent to opening five "connections to ... File option.

Recommendation: Use the KMP internal source filter (Kmpavisourcefilter) in the four options on the General tab, and open the "open files in the background" option, which is very fast to drag and drop, delaying less than the reaction time of the person. And the damaged AVI file SDXY recommended to be separated by Gabestavisplitter.

Haali drag-and-drop speed is slower than kmpavisourcefilter. In addition, if it is a H264 encoding, the PowerDVD H264 decoder (if installed) is automatically invoked. Avi+haali+cyberlink This combination is not good, will cause the color spot, the ripple, the picture discontinuity and so on.

KMPlayer

If you use Haali as an AVI separator, enforce the use of COREAVC in the custom filter manager. The recommended General tab is also set to Kmpavisourcefilter. So if Haali problem, as long as close "with Haali connection AVI", easy to convert to use Sourcefilter. into the filter control Separator General tab, the three options for the Matroska separator are gabestmkv separators (gabestmatroskasource), KMP internal MKV separator (kmpmkvreader), system default ( When the Haali is installed, the system defaults to Haali).

In addition, if you open the Connect MKV with Haali separator on the filter Control Source Filter Other tab, ignoring the settings in the General tab, you must separate MKV with Haali.

The three separators are fast, slightly slower than the human response, and very good for multiple track support.

kmplayer*. WMV (also known as ASF):

Select from the WindowsMedia tab of the source filter, and once selected, the rest of the system does not change the separator used.

"Automatic Selection" is recommended.

Of the five options:

The WindowsMedia source filter cannot be run.

KMP Internal ASF Separator, the progress bar shows a problem.

KMP Internal ASF Reader/source filter, default selection when auto Select. Drag and drop speed is very fast, but some files near the end may not drag and drop, the total time calculation error.

The new wmasf Reader (Wmasfreader) is dropped normally, but slowly, opening some files too slowly.

There is no obvious difference between system defaults and Wmasfreader.

KMPlayer

*

. rs|

For MPEG2, Gabestmpeg2splitter can be used in most cases. Subtitle calibration is based on it, and only gabest supports DTS tracks in TS.

For H264, by CPU grade from high to low preferred Nero/haali (dual core), Elecard (most users), PDVD7 (Low configuration).

First say set, and then judge the pros and cons of each separator.

There are two ways to set the TS separator:

It is best to set the "MPEG2 (TS) separator" In the General tab of the separator, very reliable and immediate. Of course, the premise is that there is no separator in the custom filter manager to turn on force, and no source filters (only two, Mpegsource and Haali) are "set as source Filters" here. The "Set as Source filter" effect is equivalent to "force connection to various types of files."

If Elecard or moonlight is installed, the "system defaults" in multiple separators here are Elecard or moonlight.

It is recommended that you do not add any separators in the custom filter manager in this style.

Another style is to use the mandatory feature in the custom filter manager, which has precedence over the settings in the General tab when the separator is "forced to use". If only one is "mandatory", KMP will definitely choose it. If you have more than one turn on force, competition KMP's favor by priority value and position. The "force-use" separator in the first place is the end-used separator, but it is also possible to use Elecard as a "system default". Here's the premise: there is no source filter here "set as Source filter." This style is good with ripe.