LAN and WAN interface standards

Source: Internet
Author: User

I. LAN interface cable standards

10base-t: twisted pair cable, generally using RJ-45 connector; maximum effective transmission distance is 100 m from the hub, even high-quality 5 category twisted pair can only reach 150 m. The matching resistance is 120 Euro.

10base5: coarse coaxial cable with plug-in connector and baseband signal. The maximum supported length is 500 m and the maximum segment is 100. The matching resistance is 75 Euro.

10base2: thin coaxial cable. The connector uses the industrial standard bnc connector to form a t-type socket. The use range is only 200 meters. Only 30 computers can be used in each segment, and the maximum number of segments is 30. The matching resistance is 50 euro.

100base-tx: cat5 or more twisted pair wires. the maximum length of the CIDR block is 100 MB.

100base-fx: one pair of multimode or single-mode optical fiber is used. When using multimode optical fiber, the maximum distance between the computer and the hub is 2 km, and the maximum distance is 10 km when using single-mode optical fiber.

1000base-t: cat5 or more twisted pair wires. the maximum length of the CIDR block is 100 MB.

1000base-f: a pair of multimode or single-mode optical fiber cables can be up to 3 km-m500m from the computer to the hub when multimode optical fiber is used. The maximum value is when single-mode optical fiber is used.

1000base-lx can be connected to single-mode optical fiber; 1000base-sx can only be connected to multimode optical fiber.

Base-lx transmit 5 km with Single-Mode Optical Fiber

1000base-lx uses multi-mode optical fiber (50um) to transmit 550 m

1000base-lx uses multi-mode optical fiber (62.5um) to transmit 550 m

1000base-sx uses multi-mode optical fiber (50um) to transmit 275 m

1000base-sx uses multi-mode optical fiber (62.5um) to transmit 550 m

100base-fx Single-Mode module transmits 10-20 km Data Using Single-Mode Optical Fiber

100base-fx multi-mode module transmits 2 km Data Using Multi-Mode Optical Fiber

Ii. wan interface cable standards

E1: 64k-2mbps.

X25: The maximum speed is 64 kbps.

Frame relay: The e1 circuit is used, and the speed can be 64 K to 2 mbps.

V24: the router end is a db50 connector, and the external network end is a 25-pin connector.

In asynchronous mode, the link layer protocol ppp is encapsulated and Network Layer Protocol ip address and ipx are supported. The maximum transmission rate is 115200bps;

In synchronous mode, link layer protocols such as x.25, frame relay, ppp, hdlc, slip, and lapb can be encapsulated. ip and ipx are supported, and the highest transmission rate is 64000bps.

Transmission Distance: it is related to the transmission rate, such as 2400bps-60m; 4800bps-60m; 9600bps-30m; 19200bps-30m; 38400bps-20m; 64000bps-20m; 115200bps-10m.

V35: The vro is a db50 connection and the external network is a 34-pin connection.

V35 cables are generally used only for synchronous data transmission. They can encapsulate link layer protocols such as x.25, frame relay, ppp, slip, and lapb on interfaces, and Support Network Layer Protocol ip addresses and ipx.

V.35 cable transmission synchronization mode) is recognized as the maximum rate is 2048000bps2mbps ).

Transmission Distance: it is related to the transmission rate, such as 2400bps-1250m; 4800bps-625m; 9600bps-312m; 19200bps-156m; 38400bps-78m; 56000bps-60m; 64000bps-50m; 2048000b.

Below are several common but important control signals in v.24 and v.35 procedures:

Dtrdata terminal ready, data terminal ready)

Dsrdata set ready data preparation), mainly used to transmit negotiation information between devices.

Dcddata carrier detect data carrier detection), used by devices to detect the current link status.

Rtsrequest to send requests)

Ctsclear to send clear and send)

Bri: Connector With RJ-45 crystal head. The bandwidth customized for interface procedures is 2b + d, with a total bandwidth of 128 kbps.

Ce1: the available time slot range is 1 ~ 31. Time slot 0 is used for system synchronization and cannot be used for data transmission. Each logical interface features the same as the synchronous serial port. It supports link layer protocols such as ppp, frame relay, lapb, and x.25, and network layer protocols such as ip and ipx.

Router ce1/pri interface is a db-15 matrix) connector, on the network side is a bnc head or RJ-45 crystal head connector.

Currently, a conversion adapter from a 75 Euro copper axis cable to a 120 euro shielded twisted pair cable is generally used to connect the ce1/pri cable using a RJ-45 connector.

Pri: 30 out of 32 time slots, and the other 0 time slots are used for system synchronization. 15 time slots are used for d-Channel Transmission signaling and cannot be used at will.

The pri interface provides a total bandwidth of 30b + d, totaling 2048 kbps.


Contact Us

The content source of this page is from Internet, which doesn't represent Alibaba Cloud's opinion; products and services mentioned on that page don't have any relationship with Alibaba Cloud. If the content of the page makes you feel confusing, please write us an email, we will handle the problem within 5 days after receiving your email.

If you find any instances of plagiarism from the community, please send an email to: info-contact@alibabacloud.com and provide relevant evidence. A staff member will contact you within 5 working days.

A Free Trial That Lets You Build Big!

Start building with 50+ products and up to 12 months usage for Elastic Compute Service

  • Sales Support

    1 on 1 presale consultation

  • After-Sales Support

    24/7 Technical Support 6 Free Tickets per Quarter Faster Response

  • Alibaba Cloud offers highly flexible support services tailored to meet your exact needs.