No wiring by Setup diagram

This tutorial is about router setup, and the wireless card installation is not written here. First installs the wireless network card, picks up the wireless route. Here is the TP LINK of the 54M wireless Broadband router tl-wr340g+ as an example.

Wireless network Card We do not add IP address, on the default automatically access. Double-click the Wireless network icon in the lower-right corner. As shown in Figure 1

Initial connection, will prompt, this is I have not yet added password, dot still connected, as shown in Figure 2

After the connection, we can start to access the router, open IE, figure 3

Enter in the Address bar, 192.168.1.1 carriage return

Note: The default IP address for the Tp-link router is: 192.168.1.1 username and password are: admin

In the pop-up authentication window input, username and password. Figure 4

Into the Routing Management page, the first entry will automatically enter the Setup Wizard page, as shown in Figure 5

Click Next to start setting, we are here ADSL Internet, so choose PPPoE, Figure 6

Then enter the account number and password that we have on the Internet, Figure 7

And then to the wireless set up, our No line from of course to open the wireless connection, SSID, we will be the default tp-link_372e70, you like the words can be changed by themselves, in a number of wireless networks can be very convenient to identify themselves. Figure 8

Set a password, in order to facilitate the settings, I am here to do 12345678 password, you can define your own password. A minimum of 8 digits Oh, of course, the more complex the password, the better.

After the password is set up, you can finish the point, Figure 9

No line is to be restarted to take effect, it automatically restarts, figure 10

If you are using a wireless connection, after the router reboot to reconnect, at this time we will see that the wireless network in the Tp-link_372e70, there will be a yellow lock, we point to connect, figure 11

We are prompted to enter the password, which is the network key, which is the 12345678 password we just set.

Connecting now, Figure 12

The connection is on, see hint, figure 13

So we can get on the Internet.

To be safe, we have to change the encryption method, preferably with WPA-PSK/WPA2-PSK AES encryption method, as shown in Figure 14

But this is not enough, now a lot of software can be cracked or found that we set the password, in order to be safe, we also want to route the default username and password is that admin has changed, and then the Mac to open the filter function, the following methods: Figure 15

Note: Before the MAC address of your host has not been added and enabled, do not start MAC address filtering, which will cause the current connected computer can not access the route and the Internet, must add the MAC address and make it effective after the MAC address filtering function. Remember, remember!

MAC address Viewing method: Start, run, enter cmd carriage return, Figure 16

Enter in cmd window: ipconfig/all

Note,/Before the space,

This is our wireless network card MAC address, write down this MAC address, and then back to the router's page, enter this MAC address

Description is convenient to remember which machine name, you can define their own, such as: XX books or something.

If you have more than one wireless Internet connection, then you should also add the MAC address of other machines, or you will not be blamed for not going to the Internet.

All right. The tutorial is finished!

Here are a few issues that may occur during Setup:

One. Can search the wireless network, but not the connection?

Check that the SSID of the wireless adapter is the same as the SSID set by the router, if it is not the same, it is not connected.

Or we later changed the encryption method, is WPA2-PSK AES encryption method, in the wireless card above also to be set to the same, if not the same will not be able to connect.

Two. QQ, but can not open the Web page?

This is not the result of DNS, we used to change the IP to automatic, there is such a problem we have to manually add IP and DNS address, the method is not written here, referring to the route I wrote earlier in the tutorial set the method.