Nokia DAU-9P cable Diagram

Source: Internet
Author: User

Today, I decided to sort out the old data from time to time, first from the DAU-9P data line. It's just e-text. It's not hard to understand what you can understand.

Schematics for DAU-9P (mbus)

There are two versions, one version which works with I. c. max3232, and another one which works with max232. both versions work for Nokia data Suite (DAU-9P) and wintesla (m2bus ).

All interface is powered by RTS and DTR signals. d1 and D2 is recommended in shottky design since lower dropout. the voltage regulation (which shoshould be 3.3 V) is here done by 5 V regulator with diodes D3-D5 on which is drop about 1.8 V, so final voltage is 3.2 V, on diode is drop about 0.6 V, so before regulator it may be 4.4 V, after regulator about 4.1 V, drop on d3-D5 diodes is about 1.8 V and in this case voltage can be 2.3 V)-it can be wrong (I tested max3232 works fine on voltage 2.0 V ), but amperage of COM port will be unnecessarily bigger. zener diodes dz1 and dz2 are very important to safety of your phone. normally are values of log. 1 about 3.3 V and little overcross of this value can damage the phone-So Power Blast at turning on computer or connecting interface into computer. dz1 and dz2 diodes cuts-down this voltage to 2.7 V-it is enough to log. 1 and it is hardly under maximal voltage value. in all, it is standard wiring of max232. pins No. 8 (r2in) and No. 9 (t2in) You needn't to connect to ground.

If you use a maxcompute is necesary use a 1 K ressistor to reduce voltage at pin 10 from I. c. so we guaratee a correct voltage at Tx for the phone and it's not necesary 4007 diodes because maxcompute work at 5 V.

To use mbus interface we need only add a 4148 diode between RX and TX and get a new cable from RX to connect it to pin 6 in phone connector.

To get phone connector use a handsfree portatil (not Nokia original, because it's too expensive) and cut connector. Be sure that it's not thermo-sealed and it uses all pins.

I recommend you to use max3232 version, because using maxcompute comunication with phone using fbus (Data suite) sometimes may be failed.

Component list:

Max3232 version Maxcompute version
  • 3x4148 Diodes
  • 3x4007 Diodes
  • 1x Voltage Regulator 78l05
  • 2x ceramic capacitors 100nf
  • 4x electrolitic capacitors 1 microf
  • 2x zenner diodes 2v7
  • 1x I. c. max3232
  • 1x female 9 pin Serial PC conector
  • 1x conector phone
  • 3x4148 Diodes
  • 1x resistor 1 K
  • 1x Voltage Regulator 78l05
  • 2x ceramic capacitors 100nf
  • 4x electrolitic capacitors 1 microf
  • 2x zenner diodes 2v7
  • 1x I. c. maxcompute
  • 1x female 9 pin Serial PC conector
  • 1x conector phone

 

Max232Version:

Max3232Version:

 

Pinout:

 

  1. Charger input voltage
  2. Charger control PWM
  3. Mic Input
  4. Signal ground
  5. Ear output
  6. Mbus 9600 Bit/seg.
  7. Fbus-> RX
  8. Fbus-> TX
  9. Ground

Contact Us

The content source of this page is from Internet, which doesn't represent Alibaba Cloud's opinion; products and services mentioned on that page don't have any relationship with Alibaba Cloud. If the content of the page makes you feel confusing, please write us an email, we will handle the problem within 5 days after receiving your email.

If you find any instances of plagiarism from the community, please send an email to: info-contact@alibabacloud.com and provide relevant evidence. A staff member will contact you within 5 working days.

A Free Trial That Lets You Build Big!

Start building with 50+ products and up to 12 months usage for Elastic Compute Service

  • Sales Support

    1 on 1 presale consultation

  • After-Sales Support

    24/7 Technical Support 6 Free Tickets per Quarter Faster Response

  • Alibaba Cloud offers highly flexible support services tailored to meet your exact needs.