Page 1/2

There should be no one at the very beginning. When everyone is getting started, it is really interesting to assemble their own computers. In particular, the assembly process combines some components, after power insertion, I was moved when I waited for B to start up. I remember that 15 years ago, I didn't have to change the software disk to play games. The first time I bought the zero component was a 20 mb Seagate hard drive. I read and read the book while I touched it. I was also inexplicably installed and formatted, looking at the world of food, there was no pause while changing the map. I was almost not touched by the tears, and I started to stop the DIY hardware.

It may be a subjective view. The DIY market seems to be getting weaker and weaker, and Evergrande's first-line manufacturers are constantly suppressing second-and third-line price wars, the centralized business area does not seem to have a great deal of time in the major brands ten years ago, and the price competition is only one of them. As for how to avoid in-depth discussion, it seems a little different from the topic, if you are a newbie or a beginner, this article may be helpful. As for veteran birds, please advise on errors or suggestions.

The most basic computer host is equipped with a motherboard, CPU, memory, video card, power supply. With these things, you can see the BIOS at boot, however, you still need to store devices (hard disks, CDs, and soft discs ......) In order to make the computer look like a computer and security considerations, the chassis is essential for general users, but at this time many people may wonder, players in the discussion board do not need to use a shell for testing! Those uncles have been trained, usually for ease of disassembly and Assembly during testing. If your computer is to be used like normal people, don't save the money.

The following is a list of components involved in this Assembly:

CPU: AMD Sempron 3000 +
CPU radiator: the original fan is included in the CPU box
Memory: DDRII 667 1GBx2
Motherboard: MSI K9AGM2
Graphics card: built-in display of the motherboard
Hard Disk: hitachi sataii 160G
Optical Drive: NEC 16X DVD-RW
Power Supply: up to 350 W
Chassis: Cooler Master Elite 340

Zero component list

In addition to the above, you also need a moderate size and improved cross screw, and a flat desktop.

In the beginning, you can start from the CPU and install the CPU first to the motherboard. Because the space in the chassis is limited, it would be difficult to install the motherboard first to the chassis and then the CPU ,, if the wrong foot position of the CPU is not installed, take the CPU of AM2 as an example. There is a golden triangle icon on the CPU, and the triangle icon pointing to the socket seat on the motherboard is gently placed in, if not, check whether the foot position is correct or the foot on the CPU is skewed.

There is a golden triangle icon on the CPU

After putting it in, press the tenseton down to fix the CPU.

Fixed CPU

The next step is to install the CPU radiator. The original fan is quite simple to install. Before installation, the CPU should be coated with plaster. The main purpose is to make the CPU and the radiator have close contact, to achieve the best heat dissipation effect, as shown in, the original fan will be directly pasted with a paste on the base, at this time you do not need to smear paste on the CPU, if you have a better paste can be used, you can use the oil to wipe the base paste, pay attention to the smear paste is mainly to make the CPU can be fully exposed to the radiator base, not the more the better, a thin layer can be, I have seen someone apply "whole" CPU, including the back and pins of the CPU... This will not make the CPU cooler.

Install CPU radiator

Place the groove of the CPU radiator on both sides of the Scoket seat, and tighten the snap-on.

Tighten the snap-on

This is done. Then, find the pin of the cpu fan on the motherboard and plug in the FAN power cord of the radiator. The new one is 4pin and there is an anti-stay device, the reverse interface cannot be inserted.

Then you can first plug in the memory, the memory has a stay-proof device, there is a groove in the middle of the place, as long as you want to insert at the motherboard, you can avoid the plug-in back to burn the memory, we usually buy two identical memory channels to run dual channels. Some motherboard specifications are different, and there may be four slots. As for which two slots will start dual channels, we have to look at the instructions, there should be no such annoyance if there are only two slots.

Memory Installation

You can put the motherboard next to it, take out the screws in the casing, and first find the copper column to lock it to the casing. The Hole Position of the lock should pay special attention to the Hole Position of the motherboard, if there is a copper column at the bottom but it does not correspond to the Hole Position of the motherboard, if the copper column is at the bottom of the motherboard line is very likely to cause a short circuit, please pay special attention.

Chassis Installation

You can lock the power supply before locking the chassis of the motherboard. Some chassis are not very large. If you lock the motherboard first, the power supply may be difficult to install, install the I/O bezel attached to the motherboard.

Chassis Installation

When installing the motherboard, you still have to remind me that all the copper columns on the chassis must correspond to the holes on the motherboard. If it is because the installation is burned out, It is artificial! Not covered by warranty.

Install the motherboard in the chassis

Screw Tightening

After the motherboard is installed, you can pull up some of the I/O functions of the chassis. Generally, the frontend sound effects and the USB interface are common, such as the line of the frontend sound effects, which can be easily found on the motherboard, because the location of each motherboard is not the same, you can find it in the motherboard specification, most of them will have a stay-proof device, pointing to the plug-in with missing feet is correct.