Photoshop adds a sweet orange green to the fruit girl.

Source: Internet
Author: User

The material picture is a bit darker and the characters are not prominent enough. When dealing with the color of the high light area into a more vivid warm, and keep some of the dark green and cyan, and then the character of a little ruddy.

 Original


Final effect


1, open the material picture, create the optional color adjustment layer, the yellow, green adjustment, parameters and effect of the following figure. This step mainly turns yellow into orange red in the picture.

< map 1>

< map 2>

< map 3>

2. Press CTRL + J to copy one layer of the current optional color adjustment layer and change the opacity to: 50%, as shown below.

< map 4>

3, create an optional color adjustment layer, yellow, green, green, white to adjust, parameter settings such as Figure 5-8, the effect is shown in Figure 9. This step also adds orange red to the picture.

< map 5>

< map 6>

< map 7>

< map 8>

< map 9>

4, create hue/saturation adjustment layer, the yellow adjustment, parameter settings, such as Figure 10, after the mask to fill the black, with a white brush to the upper left corner of the local wipe out, as shown in Figure 11. This step turns the yellow of the high light part into orange yellow.

< map 10>

< map 11>

5, create a new layer, press the letter key "D" before the background color back to the default black and white, and then select the menu: Filter > Render > Cloud, select the Gradient tool, color set to black and white, and then from the upper left corner of the lower right corner pull white to black linear gradient. The blending mode is changed to "Color Filter", and the opacity is changed to: 70%, the effect is shown below. This step adds a high light to the picture.

< map 12>

6, create a color balance adjustment layer, the shadow, midtones, high light adjustment, parameter settings such as Figure 13-15, determined to press CTRL + ALT + G to create a clipping mask, the effect is shown in Figure 16. This step adds a warm color to the cloud.

< map 13>

< map 14>

< map 15>

< map 16>

7, press CTRL + J to copy the current color balance adjustment layer, the opacity to: 50%, the same method to create a clipping mask, the following figure.

< map 17>

8. Create a new layer, press CTRL + ALT + Shift + E-stamp layer, and blur the next figure selection with the Blur tool.

< map 18>

9, the background layer to copy a layer, press CTRL + Shift +] top, and then hold down the ALT key to add a layer mask, with a white brush to the characters face and skin parts, the following figure.

< map 19>

10, create a color balance adjustment layer, the high light adjustment, parameter settings, such as Figure 20, determined to press CTRL + ALT + G to create a clipping mask, the effect is shown in Figure 21.

< map 20>

< map 21>

11, create brightness/Contrast adjustment layer, the appropriate increase in brightness and contrast, parameter settings, such as Figure 22, to determine the previous method to create a clipping mask, the effect is shown in Figure 23.

< map 22>

< map 23>

12, the creation of optional color adjustment layer, red, white to adjust, parameter settings such as Figure 24,25, determined after the same method to create a clipping mask, the effect is shown in Figure 26.

< map 24>

< map 25>

< map 26>

13, create curve adjustment layer, the RGB, green, blue channel adjustment, parameter settings such as Figure 27-29, determine the same method after the creation of clipping masks, the effect is as shown in Figure 30. This step is to fine-tune the character's complexion.

< map 27>

< map 28>

< map 29>

< map 30>

14, create a solid color adjustment layer, color set to light yellow: #F9ECA3, to determine the mask filled with black, with a white brush to the upper left corner of the section, and then change the opacity to: 50%, the effect of the following figure.

< map 31>

15, a new layer, stamped layer. Select menu: Filter > Blur > Motion blur, Angle set to 45 degrees, distance set to 165, after the blending mode is changed to "soft light", the opacity to: 50%, the effect of the following figure.

< map 32>

16, using the Lasso tool to check out the selection shown in the following figure, feather 65 pixels and press CTRL + J to copy the selection part of the image to the new layer, the opacity to: 50%, the effect of the following figure.

< map 33>

17, the creation of optional color adjustment layer, yellow, green, white, black to adjust, parameter settings such as Figure 34-37, the effect is shown in Figure 38. This step mainly to the picture of the high light part of the increase in light cyan.

< map 34>

< map 35>

< map 36>

< map 37>

< map 38>

Finally, rub the skin of the character, fine-tune the color and the overall colors, complete the final effect.

Category:
    • PS Image Processing

Contact Us

The content source of this page is from Internet, which doesn't represent Alibaba Cloud's opinion; products and services mentioned on that page don't have any relationship with Alibaba Cloud. If the content of the page makes you feel confusing, please write us an email, we will handle the problem within 5 days after receiving your email.

If you find any instances of plagiarism from the community, please send an email to: info-contact@alibabacloud.com and provide relevant evidence. A staff member will contact you within 5 working days.

A Free Trial That Lets You Build Big!

Start building with 50+ products and up to 12 months usage for Elastic Compute Service

  • Sales Support

    1 on 1 presale consultation

  • After-Sales Support

    24/7 Technical Support 6 Free Tickets per Quarter Faster Response

  • Alibaba Cloud offers highly flexible support services tailored to meet your exact needs.