PS teach you to draw cool Kobe basketball poster

Ke mi friends to collect the tutorial! Today, a Kobe Bryant flying shooting poster tutorial, the effect of cool, meticulous process, the operation of the interface of Chinese, to ensure that beginners can easily learn, the weekend to one.

Let's start my drawing process by building a new canvas that matches the size of my display.

Create a new layer to fill the gradient.

I have a picture of the clouds from Baidu right.

Enlarge the entire screen, the transparency to 45 or so, do not need to be too obvious, the layer blending mode to "soft light."

Continue to take a picture of the nebula, from the original image I seem to vaguely see the elements of the nebula, so I right-click a picture of the nebula.

Change the nebula's layer blending mode to "overlay" and the opacity to 85%, adding a "black and white" adjustment layer clip mask on the nebula.

Select the "Black and white" adjustment layer, Shift+ctrl+alt+e stamped, perform "filter-pixel-Mosaic".

Alt-click the Add Layer mask icon below the layer bar to add a mask that hides all, and scribble a few strokes at the center of the canvas with a white brush. Change the layer blending mode of this mosaic layer to "lighten".

Copy the mosaic layer and perform the filter-style-find edge.

Reinforce this edge effect with a threshold. Change the layer blending mode to "divide", the transparency is adjusted to 4% or so, can faint see edge on line, too obviously too contrived.

I think the color is a bit deep, a new layer, with 2c4257 color at the top smear some, and then the layer blending mode to "linear Dodge (Add)", the transparency also lowered a little.

Create a new layer, and use a black brush to cover the edges too brightly.

Enter a 24 white text size of about 160 pixels, change the layer blending mode to "overlay", and transparency 50%.

Copy a layer. The bottom layer of the 24 grille after the Gaussian Blur 3.0, to the left to move some distance.

Select "Polygon Tool", set to 6 sides, according to the rules of the honeycomb copy out, change the layer blending mode to overlay, transparency is 63%.

Select Rounded Rectangle tool, fillet radius as much as possible to set a large, draw a two-smooth strip, the length is roughly the same as "honeycomb", add a mask, the right gradually fade.

Enter the name of Kobe Bryant with a Imitari extended font size of 22 pixels, and add a projection. The font is a bit different from the original, but it's similar.

Copy one layer, clear off the layer style, ctrl+t the same proportion to enlarge 200%.

After Gaussian Blur 3.0, change the layer blending mode to overlay.

Continue copying a layer of text, and in the layer, right-click "Convert to Shape".

Ctrl+t magnification 117%, press a box to select all the letters after CTRL + C copy, delete this layer, in the Honeycomb layer Ctrl + V with "minus" mode paste, adjust the position of each letter.

Select the Rectangle tool to draw a white strip, rotate it, place it in the left position, change the layer blending mode to overlay, and reduce the transparency.

Put the Cape Kobila in, adjust the size and use the pen to pull out his outer contour.

Reduce some of the saturation.

Add a blue solid color adjustment layer to change the color of the jersey, I used a multiply-stacked blending mode.

Use a curve to enhance the contrast of Kobe Bryant, in fact, the "brightness contrast" is similar, but I think the curve adjustment more delicate.

Now the jersey is a bit fake, it doesn't have a high light, all the highlights are covered in blue, copy the Blue channel in the channel, adjust with the color level, let the highlight point.

Press CTRL on the blue copy of the left mouse button to copy the selection, back to the layer, create a new clipping mask layer, fill it with white, lower the opacity appropriately, add a layer mask, selectively reduce the brightness of light in some places, such as bare skin, sneakers and so on, now this blue jersey looks much more than it was.

Create a new layer below Kobe Bryant and use the Paint bucket tool to select a pattern fill that I made at first. It's a very simple pattern, not to elaborate here.

This is the effect of the fill completion.

Change the fill layer blending mode to overlay.

Ctrl-click the left mouse button on the red channel to copy the selection, back to the layer bar, a new layer under the stripe pattern fill layer, fill the white, hold down ALT, click the left mouse button on Kobe's Mask to copy the mask to this white fill layer, which is my hidden effect of the Kobe layer.

Reduce the transparency of this layer to about 70, enlarge 116%, slightly rotate some angles is not no good.

Duplicate a layer, continue to enlarge the rotation, transparency to 10 or so.

Press CTRL to click the left mouse button on Kobe's Mask to copy the selection, create a new layer under the striped fill layer, rotate the transform selection, and enlarge the rotation.

Right-click to select a stroke.

Do not cancel the selection, transform the selection again, and also enlarge the rotation after the stroke.

Lower the opacity of the stroke layer, add a mask, and smear the bottom.

The masks of the two phantom layers also do some fading processing.

Set a simple brush.

CTRL + the left mouse button in Kobe's panel to copy the selection, adjust the fringe fill layer under a new layer, scribble a few.

Continue to click a few after you cancel the selection.

Change this layer-fly blending mode to overlay.

Continue to set the brush, here I only canceled the scatter.

Draw a pen at random.

Ctrl+t adjust the size and angle.

Change the layer blending mode to overlay, while reducing transparency.

Paste a scratch on the material.

Reduce the transparency and change the layer blending mode to filter color.

Add masks, and do some processing on the lower left corner.

The effect of the final completion.

Category:

• PS Image Processing