Contrast chart
Adjusting the curve, brightening the image, merging the graph layer and the background layer
1. Open the original piece, perform the adjustment layer/curve.
Adjust Layer/curve
2. Highlight the image appropriately.
Image Highlight
Merging layers
3. Combine graph layer and background layer.
Second, with the filter liquefaction command, the character face repair thin
1. Perform the filter/liquefaction command on the background layer.
Filters/liquefaction
2. Select the first Liquefaction tool on the left to trim the face of the character properly.
To fix a thin face
3. Select the Stamp tool, the opacity is about 30%, repair the flaws on the skin of the character.
Fix off the skin flaws in the character
Third, adjust the color
1. Execute selection/color Range command.
Select Color Range
Eyedropper Pick Color
2. Use a straw to draw the most bright area of the person's skin, color tolerance 27.
Four, select the reverse, with the curve appropriate to highlight the area in the selection section
1. Click OK, make the selection, right click the mouse, select the reverse selection.
Select Reverse
2. Execute curve command, appropriately highlight the area inside the selection.
Highlight Area section of a selection
V. Perform optional colors
1. Perform optional color command, color-red, yellow +71 other values unchanged.
Perform an optional color command (red)
2. Color-yellow, cyan +29 Yellow-66 black +7.
Perform an optional color command (yellow)
Perform an optional color command (white)
3. Color-white, cyan +94 yellow +15 other values unchanged.
Six, stamped layer, select the gradient tool
1. Stamped layer, select the Gradient tool, click the Gradient editor, select the foreground color to the transparent color gradient, and the gradient type is a radial gradient.
foreground color to Transparent color gradient
2. The gradient color code is #f8dccb.
Gradient Color
3. Change the gradient mode to soft light.
Change the gradient mode to soft light
4. Gradient opacity is 62%, with a set of gradient tool, in the image around pull out the gradient, the effect if shown (note the Red box settings).
Pull the gradient around the image
Seven, adjust the layer to choose color
1. Perform adjustment layer/optional color-yellow, cyan-37 magenta +11 Yellow +7 black-45.
Adjust layer optional color (yellow)
Adjust layer optional color (white)
2. Color-white, cyan +49, other unchanged.
Use the Quick Selection tool to select and feather the area outside the character
1. Stamped layer, with a quick selection tool to select the area outside the character and feather, feather value of 20 pixels.
Select an area outside the character and feather it
2. Perform adjustment layer/color balance-middle tone, red-38 green +36 Blue +25 (Note: This step will be mainly refreshing some of the background).
The color balance is adjusted to the middle tune
Use Pen tool to select the lips of the characters and feather them
1. Stamped layer, use Pen tool to select the character's lips.
Pen tool to select the character mouth type
2. After the selection is generated, feather with a feather radius of 10 pixels.
Feather after generating a selection
Adjust the color balance of the lips to the middle tone
3. Perform adjustment layer/color balance-middle tone, red +21 green-4 Blue-21 (note: This step is mainly to adjust the color of the lip).
The Lasso tool makes a selection and feather in the cheek of the character.
1. Use the Lasso tool to make a selection in the cheek of the character, with a feather radius of 100 pixels.
Character Cheek Feather
2. Perform adjustment layer/color balance-middle tone, red +25 green-30 Blue-21 (note: This step is mainly used to blush).
Adjust the color balance of blush to middle tone
Use Quick selection tool to select the person's arm to feather
1. Use the Quick Selection tool to select the person's arm to feather, feather the value of 30 pixels.
Character Arm Feather
2. Adjust the layer/curve command: Use the curve to press the brightness of the hand (note: Because the brightness of the hand and the entire character of the skin is not coordinated, so use the curve to darken it).
The brightness of the pressed dark hand
12. Merge all Layers
To fix the flaws in a person's body
Effect chart
1. Merge all layers and use a stamp to fix the flaws in the character. Done.
Classification: