Htop,glances,dstat Process Management tool Introduction
1. Htop Tools
650) this.width=650; "src=" http://s3.51cto.com/wyfs02/M00/6B/76/wKioL1UuaIzBiKRbAAeOq7OBvzI310.jpg "title=" Image 0415 (2). jpg "alt=" wkiol1uuaizbikrbaaeoq7obvzi310.jpg "/>
Htop Common Interactive Commands
M: in Memory Sort
P: in CPU Occupation ratio Sort
T: in CPU time-consuming sorting
u: filter only shows processes for selected users:
S: tracks system calls initiated by the selected process;
L: displays files opened by the specified process
T: Show Process tree format
A: binds the selected process to the specified CPU on
2, Glances:
650) this.width=650; "src=" http://s3.51cto.com/wyfs02/M00/6B/7B/wKiom1UuZ7KDlQs7AAYNOhiiAlM117.jpg "title=" Image 0415 (3). jpg "alt=" wkiom1uuz7kdlqs7aaynohiialm117.jpg "/>
GLANCES[-BDEHMNRSVYZ1] [-B bind] [-C Server] [-C conffile] [-P port] [-P password][--password] [-t refresh] [-f file] [-O Output
Common options:
- B: in byte/s Display network card device data exchange rate for units;
- D: Close Disk I/O function module;
-f/path/to/somefile : Set the location and format of the output file;
-O {html| CSV}:
- m: Close Mount function Module
- N: Turn off the network function module
- R: Close the Process List feature module
- t #: Specifies the length of the delay, which defaults to 3 seconds;
-1 : Each individual display CPU relevant load data information;
glances Remote mode support
Service-side Mode
Glances–s–b ipaddr
Client mode
Glances–c ipaddr
3, Dstat Tools
650) this.width=650; "src=" http://s3.51cto.com/wyfs02/M00/6B/7B/wKiom1UuZ-bDbh0sAAE4ML2PNuM966.jpg "title=" Image 0415 (4). jpg "alt=" wkiom1uuz-bdbh0saae4ml2pnum966.jpg "/>
Dstat: integrates the Vmstat, Iostat, netstat andifstat Four tools of the function;
Dstat [-AFV] [options:] [Delay [Count]]
C: Show CPU statistical data related to performance indicators;
- D: Show Disk correlated rate data;
- G: Show page correlated rate data;
- I.: Show Interrupts Interrupt correlated rate data;
- L: Show average Load Load Average ( a) relevant statistical data;
- m: Show Memory ( a) relevant statistical data;
- N: shows the rate of data sent and received by the network;
- N: displays the rate at which the specified NIC is sending and receiving data ETH
- P: Show Process (non- disruptive processes and new processes ) the relevant statistical data,
-r:io The rate of the request;
- S: Show Swap the relevant data
- y: Display System-related data, including interrupts and process switching;
--top-cpu : Displays the most occupied CPU the process;
--top-bio : Displays the most consumed Block IO the process;
--top-io : Most occupied io the process;
--top-mem : Displays the most memory-intensive processes;
--IPC: shows the rate data related to interprocess communication;
msg Signal SHM Shared Memory
--aio: Asynchronous IO
--raw: Show Raw The relevant data of the socket;
--tcp: Show TCP data related to sockets;
--UDP: Show UDP data related to sockets;
--unix: Show Unix sock interface-related statistical data;
--socket: Show
-a:-cdngy
Pstree,ps,top,htop,vmastp,pmap,glances,dstat Process Management Tool Introduction