with
Manual Operation
Msoobe.ext Enable the configuration method,Quick FIX: Windows Setup cannot configure Windows to run on this computer's hardware
I installed my own encounter is blue this error, the following this also has netizens said to install the driver and other methods to solve.
Note: The main content of this article is transferred from other netizens, I was in Dell new INS 15r-3521 installation Win7 64-bit encountered this situation,
swapped HDD mode, installed SATA drive cannot be resolved
, re-installed 7 times, later found this article on the error page start DOS command mode manually runMsoobe
to configure
.
the same machine installation Win7 32 is absolutely no problem, there is a problem with 64 bit.
Important: After entering the command, configure it, click Strong to close the error. If you reboot to "rollback" do not go in, otherwise it will be removed from the installation. Since the previous installation, there is a Windows 7 menu, directly Click this to go in. (Go in and run Msconfig in the Startup Item Management menu to remove the rollback that's useless.) But if you don't have Windows 7 in, you might want to build a startup menu.
tossing for 10 hours of trouble, and finally solved,.
because it is too time-consuming, so the transfer and add instructions.
If this method does not solve, you can try the following users listed other solutions, such as installation of drivers.
But general installation drive This is suitable for older computers, new laptops or desktops are supported. -----------------------------------------------
Workaround:When prompted, press SHIFT+F10 will open the Command window, go to the C:\windows\system32\oobe folder, enter Msoobe return and enter Msoobe to enter the next operation, but the error box is still in, Don't worry. Follow the on-screen prompts to enter the appropriate information until you complete the installation of the system. No problems with the WIN7 system after installation.
Note: Do not DOS command, do the following: Hold down the SHIFT key and then press the F10 key, open the command window, enter CD OOBE carriage return, and enter MsoobeThe above situation generally appears in the ghost version of the WIN7 system. I have met two times, are resolved through the above method: 1. Acer D270 install win 7 32-bit flagship Ghost edition, 2.HP installed green tea Ghost WIN7 32 Professional Edition;------------------ -----------------------------have searched the internet for this problem and found some of the following solutions: 1. A netizen said that as long as the ghost system to copy to the USB stick installation can solve the problem; Some netizens have said that it will solve the problem to copy Ghost system to hard disk installation. 2. Some netizens said that it is hard drive boot problems, rebuilding the MBR can solve the problem. 3. Some netizens think it is WIN7 to hide the problem of active partition (WIN7 another way of installation, In the hard disk recommended 100MB active hidden partition for the boot file), the solution is to use the installation version of the system to install, in the steps to the partition to delete the C drive, the system will prompt to establish a hidden partition, set up a hidden partition, exit installation and then install the Ghost version of the system, Then perform a system repair installation. 4. A netizen said, to the official website of Intel Download 3 Series chipset windows 7 F6 driver, install the driver can be loaded. Analysis: 1th, 2 The solution is basically a rip-off, and the 4th is probably right, but I think the problem with driver class is usually a blue screen instead of appearing as an error prompt. 3rd, the solution is too cumbersome and too time-consuming. Cause of the problem: it should be the reason why the hard disk has two primary partitions! WIN7 installation There are two ways, one, is the WIN7 system boot files and system files are stored in the C drive (at this time the C drive is the active primary partition), and two, WIN7 boot files are stored separately in the 100MB-200MB hidden active partition, System files are stored in the C-drive (C-disk is inactive primary partition)-random WIN7 system, which is generally used in this way of installation. There are active hidden partitions of the installation of the ghost version of the WIN7 system, will be a blue screen or continue to restart the system can not successfully install the phenomenon. When you set the active hidden partition to an inactive partition and set the C drive as the active partition, it is very likely that you will encounter the scenario when you install the Ghost WN7 system.
Quick FIX: Windows Setup cannot configure Windows to run on this computer's hardware
