"Installation Failed!" in the GUI but not in the CLI (/usr/bin/winusb:line 78:18265 Terminated)

"Installation failed!" in the GUI but not in the CLI (/usr/bin/winusb:line 78:18265 Terminated)

Installation failed !Exit code: 256Log:**blank**

-----

Install log (when running winusbguiAs root)

Installation failed !Exit code: 256Log:Formatting device...Wait 3 seconds for block device nodes to populate...mkfs.fat: warning - lowercase labels might not work properly with DOS or Windowsmkfs.fat 3.0.28 (2015-05-16)Mounting...mount: /dev/loop0 is write-protected, mounting read-onlyCopying...Installing grub...Installing for i386-pc platform.Installation finished. No error reported.Installing grub.cfg...Exiting...Syncing.../usr/local/bin/winusb: 行 78: 20260 終止                  while true; do    sleep 0.05; echo ‘pulse‘;doneCleaning.../usr/local/bin/winusb: 行 78: 20593 終止                  while true; do    sleep 0.05; echo ‘pulse‘;doneUnmounting and removing ‘/media/winusb_iso_1455346491_15903‘...Unmounting and removing ‘/media/winusb_target_1455346491_15903‘...

P.S. "Finally" in the output approximately means "terminated".

______________________________________________

Installation Failed!
Exit code:256
Log:
Formatting device ...
Wait 3 seconds for block device nodes to populate ...
Mkfs.fat:warning-lowercase labels might not work properly with DOS or Windows
Mkfs.fat 3.0.28 (2015-05-16)
Mounting ...
Copying ...
Installing grub ...
Installing for I386-PC platform.
grub-install:warning:attempting to install GRUB-a disk with multiple partition labels. This is not supported yet.
Grub-install:warning: Unable to embed. In this installation, GRUB can only be installed by using a block list. However, the Block list is not trustworthy and is not recommended for use.
Installation finished. No Error reported.
Installing Grub.cfg ...
Exiting ...
Syncing ...
/USR/BIN/WINUSB: Line 78:7,273 terminated while true; Do
Sleep 0.05; echo ' pulse ';
Done
Cleaning ...
/USR/BIN/WINUSB: Line 78:12,165 terminated while true; Do
Sleep 0.05; echo ' pulse ';
Done
Unmounting and removing '/media/winusb_iso_1482765713_2306 ' ...
Unmounting and removing '/media/winusb_target_1482765713_2306 ' ...

==================================

Does Gksudo command installed on your system?

==================================

This issue are also reproduced in the following article:
Make A bootable Windows ten USB Install Stick on Linux with Winusb Fork ~ Web Upd8:ubuntu/linux Blog

====================================

I got same problem but solved now by
"Sudo apt-get install Gksu"
"Gksudo Winusbgui"
(I.e..type it without quotes)

Lin-buo-ren referenced this issue on 8 Nov Closed Installation Failure error (GUI version) #76

Lin-buo-ren changed the title from "installation failed!" on GUI but not in CLI to "Inst Allation failed! "in GUI and not in CLI (/usr/bin/winusb:line 78:18265 Terminated)

======================================================

Hi again, please use the latest revision on GitHub repo and see if it's still reproducible (it should be, as we never fixed The problem anyway).

=======================================================

I was encountered this issue right now, with Windows 10.
I ' m on Ubuntu 16.04 and Winusb 1.0.11

I tried to run the installation anyway and it worked (I just ignored the error).

=====================================================

Hi, please use the latest revision in the repository (instead of latest released version) for reproducing the issue. We ' ve have changed a quite amount of code since 1.0.11

======================================================

I got similar problem and solve it!
I Don t now why, but if you use GUI it s not work. Use command on line:
sudo winusb--format/path-to-iso-file/filename.iso/dev/sdb (or other your flash)

=========================================================

The issue title already tell this CLI (command line interface) works.
This issue are about the GUI problem

"Installation Failed!" in the GUI but not in the CLI (/usr/bin/winusb:line 78:18265 Terminated)