[Reprinted] wince7.0 is officially released. You can download the 180-day trial version.

Windows Embedded compact 7 has been out for more than half a year and has no time for it. Recently, it has a refresh version, and the computer has another 1 TB hard disk, So download it and try it out.

Let's talk about how to build the development environment. Platform Builder 7.0 is used as a plug-in for vs2008 and is not compatible with all previous versions of the wince development environment. It must be installed independently. Therefore, follow these steps to build a wince7.0 development environment:

• Install vmware workstation 7
• Install Windows 7 on a virtual machine
• Install vs2008 and SP1
• Install Windows Embedded compact 7

In the past, when learning the new version of wince, it was generally based on a simulator to create a system. However, wince7.0 currently does not support device emulator because it only supports armv5 and later processors, the device emulator is still armv4. Currently, the project uses the arm11 processor, which belongs to armv6, So we plan to transplant it directly to this platform.

New Features and porting instructions for wince7.0 are provided in the installation directory in PDF. According to the documentation provided by wince6.0, porting from wince6.0 to wince7.0 is relatively simple. Wince5.0 to wince7.0 may be difficult to transplant. We recommend that you first port wince5.0 to wince6.0, and then from wince6.0 to wince7.0.

Currently, the project uses wince6.0, so we can use 6.0 BSP as the template for porting. The porting method is similar to the introduction of S3C2410-WinCE6.0-OAL quick debugging. Copy the BSP of 6.0 to the platform directory, then clone a new BSP through platform Builder 7.0, modify the corresponding item attribute in the catalog file, and change armv4 to armv6. In addition, modify the platform. bib and platform. Reg files under the files directory to clear the contents of these two files. Modify the dirs file in the src directory to remove the directory corresponding to boot and drivers. The purpose of this operation is to quickly port the oal of wince7.0, first run the kernel of wince7.0, and then slowly transplant various drivers.

The method for creating a project in wince7.0 is similar to that in wince6.0. Create a project based on the custom device template and set platform properties. Because the BSP kitl has never been verified on 6.0, kitl is disabled first. Use clean sysgen to compile the system after setting platform properties. If you are lucky, no compilation problem occurs and you can directly generate NK. Burn it to the device and get up. The printed information after the system is started is as follows.

Windows CE kernel for ARM (thumb enabled) built on Dec 15 2010 at 16:44:21
Processortype = 0b76 revision = 6 cpuid = 0x0000fb766
Oemaddresstable = 80203b80
[Kernel] + oeminit ()
[Kernel] dcache: 128 sets, 4 ways, 32 line size, 16384 size
[Kernel] icache: 128 sets, 4 ways, 32 line size, 16384 size
[Kernel] chipid [156] [acda17d0]
[Kernel]-oeminit ()
Nkstartup done, starting up kernel. ncpus = 1
Windows CE kernelinit
Error Reporting memory reserved, dump size = 00020000
Booting Windows CE version 7.00 for (ARM)
Memory ing: Total pages: 36278, filesystem pages = 4534
Booting kernel with clean memory Configuration:
Total memory sections: 1
[0] (static): Start: 83a26000, extension/attributes: 00024000, Length: 08db6000
Scheduling the first thread.
PID: 00400002 TID: 00410002 pgpool: Reserved 768 pages for loader pool
PID: 00400002 TID: 00410002 pgpool: Reserved 256 pages for file pool
PID: 00400002 TID: 00410002 error: oalioctlhalgetdeviceinfo: Invalid request
PID: 00400002 TID: 00410002 running xst0: Platform name = wince6.0 r3
PID: 00400002 TID: 00410002 warn: oalioctlhalgetdeviceinfo: spi_getprojectname: bu
Ffer too small
PID: 00400002 TID: 00410002 running xst1 :>>> loading module 'kd. dll '(0xc0401db0) at
Ddress 0xeffe0000-0xefffe000 in process 'nk. EXE '(0x83a09ad0)
PID: 00400002 TID: 00410002 KD: Starting kernel debugger software probe (kdstub )-
Kd api version 27
PID: 00400002 TID: 00410002 running xst1 :>>> loading module 'nk. EXE '(0x83a09ad0) at
Ddress 0x80200000-0x80217000 in process 'nk. EXE '(0x83a09ad0)
PID: 00400002 TID: 00500002 filesys doesn't exist, no app started

So far, the migration of wince7.0 oal has been preliminarily completed. Although we haven't seen the wince7.0 interface yet, we have finally learned about platform Builder 7.0. Next, we can transplant the display and touch drivers to further unveil wince7.0.

 

Wince 7 http://www.microsoft.com/windowsembedded/en-us/downloads/download-windows-embedded-compact-ce.aspx