Summary of how to crack the printer ink monitoring page 1/2

Method 1: false recognition

1. When the computer prompts that the ink cartridge must be changed, add the new ink cartridge according to the normal steps.

2. Open Control Panel-printer properties-application tool-check the amount of ink. We can see that the ink is full, so do not click "OK", or close the printer power.

3. the rightmost side of the printer is the ink car, which is pulled to the place where the ink cartridge is changed. Take out the ink cartridge, switch to the original computer, and prompt that the ink cartridge has been used up. After the ink cartridge is installed, push it to the rightmost end of the printer (the ink car will be pushed back to the original place ). Then we can see that the ink is still full. Click OK to use the ink cartridge.

In addition, if you don't want to use a new ink cartridge for "guest", you can use the chips on the ink cartridge that are filled with ink, use the tips or screwdrivers, and install the new chips. For more information, see the following section.

Method 2: replace records

1. Change the ink cartridgeProgramRemove the ink cartridges from the used-up printer, and drill or tear the above seal to expose the filled ink hole. The color of the original ink cartridge is filled with ink, use a transparent tape to seal the device ).

2. Use a knife or a small screwdriver to slip the chip on the old ink cartridge filled with ink, and then install the chip on it.

3. Fill the old ink cartridges filled with ink and new chips with the printer. Then, you will see the filled ink volume of the new ink cartridges, and click "OK ".

4. After the ink cartridge is automatically returned to the end of the printer, use a small screwdriver or wire to move the ink car outward. Then, you can pull the ink car to the place where the ink cartridge is changed. (Light hands! It's easy. Never use brute force !!!)

5. Take out the ink cartridge, remove the new chip, replace it with the old chip, then install the ink cartridge, push it to the rightmost end of the printer, then push the ink car back to the original place, and then click the ink display, the read ink cartridge is full, and then click "OK". The ink is filled successfully.
Pson Inkjet Printer

Because the Epson injection ink cartridge is separated from the nozzle, you do not need to punch in. You only need a few disposable syringes to complete the task.

Before adding ink, you need to prepare broadband tape, absorbent paper, compatible with ink, pure water, disposable syringe. Extract the ink cartridges according to the ink jet printer instructions and perform the following operations (for key steps, see ):

1. Dry the holes at the bottom of the ink cartridge with absorbent paper, and stick the nozzle with a clean broadband tape (preferably with a Viscose layer, such as a membrane electrical tape.

2. You can see two small holes in the position labeled on the cartridge. The first hole is about 1cm away from the edge, and the second hole is 1.4 away from the first hole. Use a disposable syringe to penetrate the film with caution (force must be controlled very small), the first hole is the filling hole, the second hole is the ventilation hole.

3. Use a disposable syringe to absorb about 5 ml ink, push the ink hole up, and tilt 45 degrees to prevent the ink from overflowing from the balance hole in the upper part of the ink cartridge when the ink is full.

4. ink injection: the ink in the disposable syringe is slowly injected into the ink hole. The ink filling operation should be fast and slow, and repeated several times until the operation is completed. At the same time, you can use the transparent plastic shell on the left side of the ink cartridge to inject the ink to 4/5 of the cartridge capacity. It should not be too full, and then use the absorbent paper to clean the ink near the ink hole.

5. When loading the ink cartridge into the printer, pay attention to the ink cartridge inserted into the bracket, the back must be closely linked to the bracket, only the position is installed, the ink cartridge lock rod can be gently pushed in place. If the feeling is blocked, it indicates that the ink cartridge is not in the correct position. At this time, you can loosen the lock lever, move the ink cartridge up and down left and right with the left hand, and gently push the lock lever with the right hand to feel the position.

6. finally, open "My Computer → printer → properties → control center", go to "clean the Print Head", perform one or two cleanings, and ensure that the air at the exit is excluded, print a test page and you can use it.

If you want to add color ink, but the steps are a little complicated, you need to inject different colors of ink three times.

it must be emphasized that there are some troughs on the surface of the box-ventilation troughs, some of which are under the label. To ensure the consistency of the atmospheric pressure inside and outside the cartridge, the tape cannot be completely blocked when pasted, otherwise, the data cannot be printed.