Telecom Fibre Router Setup, Unicom fibre router setup

Telecom Fibre Router Setup

You put DNS set up should be OK, DNS to Baidu search your area of DNS fill the router and two computers on it.

In the URL bar input 192.168.1.1 into the account password, the manual has, click on the IP settings in the DNS input you find from the Internet in your location of the telecommunications DNS xx.xx.xx.xx has two, a main standby, are filled in, save exit, and then on both computers right click on the Network Neighborhood, Right point local connection, properties, find the Middle Internet Protocol, double-click it, manually fill in DNS and you find the same, all fill in to solve the problem of line off, the reason is the network of Internet monitoring software, you fill in the DNS after you can.

Unicom Fiber Router Setup

The specific settings are as follows:

192.168.0.1

admin, Password input: admin.

This article takes the di-740p model of broadband router D-link, the default management address is 192.168.0.1, and the management port is 8080.

Set the IP address and router management address of a computer to the same network segment, such as 192.168.0.2, open the browser of 192.168.0.2 computer, enter "http://192.168.0.1:8080" in the Address bar and press ENTER to appear the user Login prompt window, Enter the default admin account and password in the broadband router specification to enter the settings interface.

In order for the router to dial automatically, we also need to integrate the ADSL account into the router.

Click on the top of the "Home" tab, and then click on the Change "WAN", in the PPP over Ethernet see the setting of ADSL account, enter their own application for ADSL account and password save settings.

Now go to the System Information section in the System Status tab to view the networking status, where you can see clearly the network information that ADSL dial-up obtains on the WAN side.

After setting up the ADSL account, we can access the Internet through the broadband router, but in order to better manage and improve security, we need to do the following: Click "Home" tab, then select "DHCP" on the left, and set the IP address range at the IP range where the DHCP server can enter, After saving, the broadband router has the function of automatically assigning IP address.

To prevent the chaos of BT

Default settings All computers connected to the router are protected, that is, in the intranet, the use of Peer-to-peer software such as BT will be affected. We can set the declared host by using the "DMZ" in the "Advanced Settings" tab. Set up here the host is exposed to the network, on the one hand can use BT download software and establish IIS, FTP server, and on the other hand also exposed to hackers and viruses, so this computer security work must be done well. (if only to use BT and other Peer-to-peer software and the host to announce the words is very unwise, in fact, we can use UPnP function to solve the intranet can not use Peer-to-peer software problems. Click "Other Items" under the "Tools" tab of the Router settings interface, and then set UPnP to "start". )

Enter the Filter tab in the Broadband router Setup interface, we can filter the source and address of the datagram, including IP address, URL information, MAC address and regional information.

Set "Activate" IP address filtering, and then enter the IP address within the IP address range, such as 192.168.0.111. "Port range" is actually filling out the information, because the BT download using 6881 to 6889 ports, so we can filter here. "Protocol" selects TCP, and "scheduling" sets the time for the filter to take effect (the time is forbidden to see the actual situation).

Both service and security

Computers exposed to the Internet hackers and viruses may exploit vulnerabilities to attack computers, but we can solve this problem by setting up virtual servers.

Login to the broadband router Setup interface. Select the virtual server label in the Advanced Settings interface. To activate the virtual server settings, enter the relevant virtual server information. For example, we want to allow 192.168.0.112 this computer to provide FTP services, but also want to let other ports to be protected by the router, you can only virtual the FTP service. The personal IP address is set to 192.168.0.112, and the Protocol mode is TCP (the FTP service uses the TCP protocol) and the personal port (FTP uses 21 ports). Additionally, you can set the time period in which the virtual service takes effect.

Tp-link Router Configuration Guide

The basic configuration of the router, so that the computer through the router to share the Internet, the process is relatively easy to achieve; The following sections of this document mainly describe the following parts:

1, collect and judge the information, prepare for configuring the router;

2, enter the router management interface, configure the router;

3, configure the process of simple fault location to eliminate!

Pre-Configure your router (if you have a clear connection to yourself, skip to 2nd)

The first thing to be sure of is what is your "broadband access" approach?

Of course, the easiest way to do this is to call your ISP (Internet service provider) for advice, or you can make a quick decision with the way you purchased your router's previous network connection.

There are several common ways to connect hardware:

1, telephone line-> ADSL modem-> Computer

2, twisted pair (Ethernet cable)-> computer

3, cable TV (coaxial cable)-> Cable modem-> Computer

4, optical fiber-> Photoelectric Converter-> proxy server-> PC

ADSL/VDSL PPPoE: A computer running a third-party dial-up software such as Enternet300 or WinXP system with its own dialer, fill in the account and password provided by the ISP, each time before the Internet to dial;

Or your ADSL MODEM has enabled the routing function, fills in the ISP to provide the account number and the password, the dialing movement gives the MODEM to do; (this kind of broadband access mode is typical such as the "Network Express" provided by Southern Telecom)

Static IP:ISP provides you with fixed IP address, subnet mask, default gateway, DNS;

Dynamic IP: The computer's TCP/IP property is set to "Automatically obtain IP address", each time you start the computer can access the Internet; (this kind of broadband access mode typical such as Shenzhen "Tianwei video")

802.1x+ static IP:ISP provides fixed IP address, special dialing software, account number and password;

802.1x+ Dynamic IP:ISP provides special dialing software, account number and password;

Web authentication: Every time before the Internet, open IE browser, first go to the ISP designated home page, fill in the user name provided by the ISP password, through the certification before you can do other online operation;

These connection authentication methods mentioned above are only some broadband access methods with high penetration rate, of course there are other topological connections and authentication methods exist; So when you are not sure of your broadband approach, it is best to ask the ISP: their installed broadband access, IP address is static or dynamic? Is the protocol used for authentication PPPoE, 802.1X or Web authenticated?