Tengda (Tenda) d301-bridge mode How to set up?

This document applies to users in the telephone line

Applicable model:D301 problem Category: Set up the Internet

The first step: connect the Good Line

Step Two: Configure the IP in the local computer connection

Step Three: Configure the Router for bridge mode

Fourth step: Broadband connection dial-up Internet settings

As shown in the following figure, directly to the household telephone line to the separator at the lines, and then a phone line to the end of the modem mouth of the separator,

The other end receives the DSL port of the D301. A network cable is connected to any LAN between the computer and the D301. To the end of another phone line to the landline,

The other end of the phone port to the separator.

Attention:

1. the normal working state of the router is the LED LAN light illuminated steady or blinking, and the DSL light is often lit.

2. If you do not need to connect the landline, then directly to the door of the telephone line to the router on the lines.

set the local connection IP address on the computer to " use the following IP address "

1. Right-click on the desktop " Network Places ", select " Properties ":

2. " Local Area Connection ", select " Properties ":

3. Double-click Internet Protocol version 4 (TCP/IPV4) :

4. " Use the following IP address ", and then fill in the IP, such as: 192.168.1.X (2-254), subnet mask, default gateway and ISP provided

Preferred DNS server and standby DNS server, last click " Determine "can:

Note: If your ISP does not provide the appropriate DNS server address, it is recommended that you complete the preferred DNS server as: 8.8.8.8, and the standby DNS server is empty.

1. The browser then enters " 192.168.1.1 " in the browser's address bar, and then clicks the enter key

2. Enter "username" and " password " from the page and click " login "

3. After the router's management interface, click on the upper right corner of the " Advanced " to log the advanced interface of the route

4. The picture shows, first click on " Advanced Settings ", and then click " WAN configuration ", and then click the " Add " button

5. In the pop-up page, enter the " VPI" and " VCI" values that the operator has provided to you, keep the other default configuration, and then pull down the scroll bar,

Click " Apply/Save "

Note: The VPI and VCI values are provided by your network service provider, and if you are not sure what your VPI and VCI values are,

Then please call your network service provider first, and then do the next step.

6. Click " WAN connection Settings " on the left side of the page, then click " Add " and click " next " in the Bounce page.

7. Select the WAN Port service type as " bridge mode ", then click " Next " in the scroll bar and click " Apply Save " to save the settings.

If you already have a "broadband connection" on your computer, click here to 2. dial the Internet with an existing broadband connection.

Skip the Step and dial the Internet with an existing broadband connection .

1. Create a " broadband connection and dial simultaneously "

1.1 Right-click the Network selection property on the desktop. ",

1.2 Select " set up a new connection or network " under the " Change network Settings " main Menu.

1.3 Select Connect to Internetin the set up connection or Network dialog box, and then click Next to continue with the following actions.

1.4 In the Connect to Internetdialog box, select No, create a new connection (C)option, select Broadband connection , and then click Next

Continue with the following actions.

1.5 Select Broadband (PPPoE)in the connect to the Internetdialog box.

1.6 In the connect to the Internetdialog box, fill in the " username " and " password " provided to you by your network service provider (ISP) when you run broadband , and then click Connection ",

Complete the Create broadband connection and dial-up operation.

Note: If your broadband "username" and "password" contain letters, you need to be sensitive to case sensitivity.

2. Use the existing " broadband connection " for dial-up Internet access.

2.1 Double click on the " Broadband connection " on your computer desktop.

2.2 Enter the " username " and " password " provided by your ISP in the pop-up dialog box , and then tap Connect .

Note: If your broadband "username" and "password" contain letters, you need to be sensitive to case sensitivity.

3. if the small icon in the lower right corner of the computer screen changes to indicate that your computer has been successfully networked. You can also click the icon,

View the current network connection status, as shown in the following illustration.