The two TPLINK routers carry the WDS function for bridging.

The two TPLINK routers carry the WDS function to implement the bridging A route settings as follows: log on to the vro settings page (do not say how to do this ?) 1. Click to enter the running status. Check whether the PVC is enabled in the ADSL status. Check PVC 0 (VPI8/VCI35, telecom parameter value), PVC1 (VPI0/VCI35, the parameter values used by China Netcom and China Unicom) are enabled. Otherwise, they should be disabled. www.2cto.com 2. Click to enter the system mode and select the wireless ADSL routing mode, the default route interface is selected according to your broadband carrier (as described above). 3. Click to enter network parameters: 1) Click LAN port settings, IP Address Settings: 192.168.1.1, subnet mask: 255.255.255.0, save the configuration, and copy the MAC address. This is very important and will be used when configuring vrob B. 2) Click WAN port settings and select PPPoE as the WAN connection type, enter the data provided by your broadband carrier in the internet account and password, Select Automatic Connection in connection mode, save it, enter advanced settings, and check the manual DNS server, then, set the DNS server IP address and save and exit. You can ask your broadband carrier or Go online to check the IP address of your local DNS server of China Telecom or China Netcom/China Unicom; www.2cto.com 4. Click to enter Wireless Settings: 1) Click to enter basic settings, enter a name you like or change the SSID number. Specify a channel for the channel (copy the SSID and channel to remember and use it to set router B). It is best to set it to less than 11, this makes it easy for old-fashioned wireless networks to be connected (for specific reasons, please search online). Enable the wireless function, enable SSID broadcast, and enable the WDS bridging function, set the MAC address of AP1 to the MAC address of the LAN port of vrob B (you can log on to vrob B in advance or set vrob B before entering it), save and exit; 2) you can disable or enable wireless security settings. If you want to enable it, you must use the same security settings for vroa A and vrob B, and the password must be the same, after security settings are enabled, You must select the same encryption type and password to connect to the vro and access the internet, for more information, see the vro manual. 3) filter the wireless MAC address. It is very easy. You can understand it as soon as you can. For details, refer to the vro instructions. 5. Click Enter DHCP server, click Enter DHCP service, choose not to enable, save and quit. The remaining vro setting entries are not the focus of this application. Please refer to the vro manual and decide how to set them. Vroa A has been configured. Www.2cto.com vro B settings are as follows: log on to the vro1 settings page 1. The configuration is the same as that of vroa A. Refer to the settings. You do not need to set the settings. 2. Click to enter system mode, select the wireless routing mode. This is different from router A. Please note! 3. Click to enter network parameters: 1) Click LAN port settings, set the IP address to 192.168.1.2, subnet mask: 255.255.255.0, and save the settings. The key is to copy the MAC address. This is very important, use this function when you configure vroa A. 2) You do not need to set the WAN port. 4. Click Enter Wireless Settings. 1) Click Enter Basic settings, take out the note or raft copied when you set vroa A. Enter the SSID Number of vrossid A. That is to say, the SSID numbers of both vrouters must be the same and the channels of vrossid A must be the same, enable the wireless function, enable SSID broadcast, and enable the WDS bridging function. Set the MAC address of AP1 to the MAC address of the LAN port of vroa A and save and exit. 2) Set wireless security, the same as vroa A. The two vrouters must have the same encryption type and password. 5. Click Enter DHCP server, click Enter DHCP service, select disable, and save and exit. The remaining vro setting entries are not the focus of this application. Please refer to the vro manual and decide how to set them. Vrob B is set up now. Set the gateway of laptop A to the LAN port IP address (192.168.1.1) of router A, and the gateway of laptop B to the LAN port IP address of router A (192.168.1.1 ), the IP addresses of the two laptops, A and B, can be 192.168.1.3 and 192.168.1.4 respectively. The subnet mask is 255.255.255.0. the IP address of the DNS server is the same as that of the two routers. Test, run the command line (START-run, Enter CMD) from the notebook A and ping 192.168.1.2. If data is returned, the network is normal. If timed out is displayed, the wireless network is not set, check the network settings of the two routers carefully, especially whether the security settings are the same (if any). If ping 192.168.1.2 from laptop a and ping 192.168.1.1 from laptop B, data can be normally returned, the bridging is successful, and the rest is the Internet connection. If you cannot access the Internet, check the WAN port status of router A and whether the dial-up is successful. If not, check whether the bridge is successful. Whether the PVC settings, WAN port settings, and account password are incorrect. If the dial is successful, you cannot open the webpage. Check whether the IP address of the DNS server is correct, please be patient and check. If you do not understand more, search by keyword. Have a good time! Add www.2cto.com because I accidentally wrote a mistake (because I am used to dual-line ^ !), The gateway of computer B should also be set to the LAN port IP address of router A, which has been corrected. In your application, bridging only serves as A relay. Similar to A relay, the ultimate goal is to direct laptop B to router A as A gateway to access the Internet. In this process, the WAN port of router B does not have any data traffic, because it is useless. If you set the gateway of your laptop B to vroa A and connect it to the wireless network of vrob B, the connection is successful.