Tplink WDS wireless bridging case 3-two single-frequency wireless routers

Source: Internet
Author: User

James's house type is three rooms and two halls, the room is relatively large, more wall, use a TL-WR886N wireless router. However, the signal of one bedroom and bathroom is poor, the network speed of the mobile phone is slow, and the video is not smooth. As shown in the following figure:

I heard that the two wireless routers can be bridging, and the wireless signal can be amplified without being pulled. James plans to buy a new wireless router to bridge the amplification signal. TP-LINK staff told James, just use the new wireless router to enable the WDS function Bridge TL-WR886N, according to the guidance of the bridge is successful, you can enhance the wireless signal at home, in addition, you can achieve roaming switching during the movement process. The following figure shows the ideal results:

James according to the needs of the online purchase of a TL-WR842N as a secondary router, after the purchase of equipment, James in accordance with the following method settings.

Configuration method

Before setting WDS bridging, be sure to understand the following:

A. No network cable is required between the two routers.

B. You only need to configure WDS bridging on the secondary router.

1Enter the management interface of the secondary router

Connect the operating computer to the LAN port of the secondary Router. If you use a laptop or Pad to set it, connect to the TP-LINK_XXXX (with the Signal name on the back. Open the web browser, clear the address bar, and enter tplogin.cn (or 192.168.1.1) to log on to the management interface.

Note:: Some vrouters need to be set to 6 ~ for the first time ~ 15-bit password.

2Enable bridge application

On the management page, clickApplication Management, Find Wireless bridging, ClickEnter, As shown in the following figure:

3Start setting Wizard

After entering the wireless bridging Settings Wizard, clickStart setting, As follows:

4Scan and select the main router signal

The secondary router automatically scans the peripheral signal, selects the signal of the primary router, enters the corresponding wireless password, and clickNext Step:

Note:: If no signal is scanned, make sure that the primary router enables wireless broadcast and try to reduce the distance between the primary and secondary routers.

5Record the management of the secondary routerIPAddress

The primary router assigns an IP address to the secondary Router. You need to use this IP address to manage the secondary Router. We recommend that you write down the IP address and clickNext Step.

6Set the wireless password of the secondary router

We recommend that you keep the default value here and clickNext Step, As follows:

Note:: The wireless parameters of the secondary router can be set here, but if you want to implement wireless roaming, it must remain unchanged.

7, Confirm that the bridge is successful

Enter againApplication ManagementWireless bridging, You can see that the bridge status isBridging successful(If you use a wireless terminal, the default signal of the secondary router disappears, and the enlarged signal needs to be connected), as shown below:

8After successful bridge

Now, the wireless bridging (WDS) configuration is complete, and the final network effect is as follows:

At this time, the primary and secondary routers send the same signal, the terminal can only find one signal, and after the connection, it can automatically switch to a good quality signal to achieve roaming. James's wired computers, network TVs, and so on can use a network cable to connect to any LAN port of the primary or secondary router to access the Internet.

Answer questions

James may encounter the following problems after setting:

After completing the bridging settings, how can I log on to the secondary router management interface?

The secondary router supports three logon modes:

① Use an IP address: use the modified IP address of the LAN port to log on. For more information, see Step 2;

② Use tplogin.cn: the terminal device uses a network cable to connect to the LAN port of the secondary router or to connect to the secondary router. Enter tplogin.cn in the browser to log on.

③ Mobile APP management: on the secondary router login TP-LINK ID, mobile phone installation APP and use TP-LINK ID login, in the APP interface in the router list select secondary router for management.

Connect the secondary router after wireless bridgingWANCannot be used?

After wireless bridging, the WAN port of the secondary router cannot be used. The Internet computer can connect to the LAN port of the secondary router.

Large-Scale Price Reduction
  • 59% Max. and 23% Avg.
  • Price Reduction for Core Products
  • Price Reduction in Multiple Regions
undefined. /
Connect with us on Discord
  • Secure, anonymous group chat without disturbance
  • Stay updated on campaigns, new products, and more
  • Support for all your questions
undefined. /
Free Tier
  • Start free from ECS to Big Data
  • Get Started in 3 Simple Steps
  • Try ECS t5 1C1G
undefined. /

Contact Us

The content source of this page is from Internet, which doesn't represent Alibaba Cloud's opinion; products and services mentioned on that page don't have any relationship with Alibaba Cloud. If the content of the page makes you feel confusing, please write us an email, we will handle the problem within 5 days after receiving your email.

If you find any instances of plagiarism from the community, please send an email to: info-contact@alibabacloud.com and provide relevant evidence. A staff member will contact you within 5 working days.

A Free Trial That Lets You Build Big!

Start building with 50+ products and up to 12 months usage for Elastic Compute Service

  • Sales Support

    1 on 1 presale consultation

  • After-Sales Support

    24/7 Technical Support 6 Free Tickets per Quarter Faster Response

  • Alibaba Cloud offers highly flexible support services tailored to meet your exact needs.