Use of Netgear wgr614v9

I. Question proposal

When using Netgear wgr614v9, it is suspected that someone has logged on illegally. You need to enter the management interface and find that the password has been forgotten. Therefore, Jiang Netgear wgr614v9 vro presses the restore button to restore the factory settings. The Test password is still incorrect.

Ii. Solution

The Default User of Netgear wgr614v9 is admin and the password is password. Absolutely! Unlike other vrouters, although this password is also a common word, the confidentiality is not good, but after all, the user is shut down.

3. entry by the way

The Netgear wgr614v9 query method on the network is as follows:

Step 2Wgr614v9 Access Network

• Currently, the most common household or small office networks use ADSL access. When you use a computer to dial up the Internet, the network connection should be as follows:

• Now we need to use wgr614v9 for Internet sharing. If the computer and wgr614v9 still use Wired connection, the correct connection method should be as follows:

1. The computer should first connect to one of the four LAN ports of wgr614v9 (seeCCurve)
2. Use another network cable to connect the WAN port of wgr614v9 (the yellow port next to the antenna) to the ADSL modem (SEE)

Note:If you do not need a modem for your bandwidth and the carrier provides a network interface to connect directly to the computer, after the computer is connected to the LAN port of the router, connect the network cable from the original computer to the WAN port of the router.

Step 2: Configure Computer Network Properties

• Wgr614v9 is a browser-based device. A computer can enter the router management field through a browser to manage its configuration. However, the computer must be correctly configured first.

The following uses Windows XP Home Edition Service Pack 2 as an example to describe the computer configuration process:

2.1.Start the computer, right-click"Network neighbors"Select"Attribute"(Available on the desktop orStartFindNetwork neighbors), Right-click"Local Connection"Select"Attribute", Select"InternetProtocol(TCP/IP)", Click"Attribute":

2.2.Set the computer to"Automatically obtainedIPAddress","Automatically obtainedDNSServer addressClickOK":

Step 2 log on to the vro

3.1.Make sure that the computer is connected to one of the four LAN ports of the router in wired mode as described in step 1.

3.2.Start Internet Explorer, Netscape Navigator, and other browsers, open a webpage, and typeHttp://www.routerlogin.com Then press Enter:

3.3.1Generally, the following logon box is displayed in the browser. you can log on to the wgr614v9 Management page by entering your username and password. Default username:Admin, Password:PasswordAnd lowercase letters:

Tip]If you enter:Http://www.routerlogin.comAfter you press enter, ie does not respond or cannot open the webpage:

Check the Connection Properties in IE browser and disable proxy service: Select'Tools'→'InternetOption(Option)'→'Connection→'LAN Settings(L)'-> All options are not checked, and then select'OK'→'OK', Close the IE window, open a page again, and enter the above address in the address barAnd press Enter.

3.3.2Some users may see a prompt, please clickClose, And then open the browser again, enterHTTP:// Www.routerlogin.comPress enter to bring up the logon window:

[Description]The default IP address of wgr614v9 is 192.168.1.1. A prompt is displayed, indicating that the IP address of another network device (such as ADSL modem or another router) in your LAN is 192.168.1.1, wgr614v9 will automatically change its address to 10.0.0.1 to avoid conflicts.

3.4The first time you enter the management interface, you will first see the Netgear wireless router smart Configuration Wizard, which can guide the user to complete the settings; you can also chooseNo, I want to configure the router myself, ClickNext step, AccordingBasic Internet access settings in step 1.

 

3.5If you need to log on to the settings page again in future use, enter the correct user name and password in the logon box, and then enter the firmware update assistant.

Firmware refers to the software that is solidified in the router hardware. With the increasingly mature technology, Netgear will continuously develop new firmware for various products to further optimize the product performance. You can use this upgrade assistant to complete the upgrade operation.

Check box marked with red lines√, Indicates that every time you log on to the wgr614v9 management interface, the system will automatically search for the firmware on the Netgear server to check whether there is any new firmware release. If you want to cancel this function, check√Cancel.

Note:Because the server is not in China, it takes a long time for domestic users to use the assistant to upgrade. We recommend that users in China cancel this function. to upgrade the function, log on to the Chinese website www.netgear.com.cn of Netgear to download the upgrade file.

Note]Firmware upgrade is risky. Failed firmware upgrade may cause wgr614v9 hardware damage. Please read the Chinese website carefully before the upgrade.Firmware upgrade Guide, Or under the guidance of a professional.

Basic Internet access settings in step 1

Your network access method may be pppoe dial-up, fixed IP address, or dynamic IP address. Follow the relevant settings to complete basic Internet access settings.

4.1. pppoe dial-up Internet access configuration method

• The user name and password are required to log on each time you connect to the Internet, or the ISP provides you with a pppoe account, which is listed here. For example, China Telecom and China Netcom's ADSL Broadband services usually use this connection type, which is also used by individual residential areas.
  The following uses China Telecom's ADSL Broadband Users as an example. The information provided by the telecom operator is as follows:
  ADSL Broadband User name: gzDSL38912111@163.gd
  Password: XXX

4.1.1.First question"Do you need to log on to your Internet connection??"Select"Yes","Internet Service Provider"Select"Others", In"LoginAndPassword"Enter the broadband account and password respectively in the blank bar behind,

Internet IP address, select"SlaveISPDynamic Retrieval". If you know the local DNS server (you can call the local ISP to query it), you can select"Use the followingDNSServer", Then fill in, or directly select"SlaveISPDynamic Retrieval.

 

[Description]Wgr614v9 can beBasic settingsPage AdjustmentConnection Mode:

A. If your bandwidth is unlimited, select"Always open", The router will always stay online;

B. Select"Dial on demand", AndIdle timeoutSet a time (5 minutes by default), then the router will dial after detecting the LAN User's Internet request; if the LAN traffic to the Internet continues to be zero for more than 5 minutes, the vro will automatically disconnect from the Internet and wait for the next time the connection request is detected and then dial again;

C. Select"Manual connection"; When you need to access the Internet, first enter the vro management interface, inVro status→Connection statusClickConnectionNote that the vro will remain online after manual connection.Connection statusClickDisconnectTo disconnect from the Internet.

4.1.2.After this page is updated, open a new webpage and try accessing the internet. Under normal circumstances, you can surf the Internet! If you cannot access the Internet, clickVro status, View this pageInternet PortOfIPAddressIf the router fails to connect to the Internet, the IP address will be 0.0.0.0. Check the connection between each device and returnBasic settingsPage, check whether the ADSL account and password are correct, it is best to enter the password again. If the connection to the Internet is successful, it should be shown that the IP address and DNS are both non-zero numbers:

4.1.3.Click"Cancel"Exit management interface:

4.2. fixed IP Address used for Internet access configuration

• This type of connection is usually used for leased line access such as business optical fiber cables. The broadband service provider provides users with detailed parameters such as IP addresses, subnet masks, gateways, and DNS.
  The following uses a fixed IP address user of an operator as an example. The carrier provides the following information:
  IP Address: 192.168.0.211
  Subnet Mask: 255.255.255.0
  Gateway address: 192.168.0.1
  Primary Domain Name Server: 211.136.0000203
  Slave Domain Name Server: 61.177.95.125

4.2.1.Select"No","Internet IP Address"Select"Use static IP Address","Domain Name Server (DNS) Address"Select"Use Domain Name Server", Enter the IP address, subnet, and other information, and then click"Application", Such:

4.2.2.Click"Cancel", Exit and close the management page.

4.3. Dynamic IP Address used for Internet access configuration

• If you directly use the computer to access the Internet, the computer TCP/IP is set to automatically obtain the IP address and DNS, and you do not need to run any dial-up or connection programs, then you belong to this access method. Cable TV (Cable) and broadband in some residential areas use this connection method, such as Shanghai youlintong, Guangzhou Zhujiang broadband, and Shenzhen tianwei video.

Note:Some ISP-provided access methods adopt Web Authentication-each time before accessing the internet, you must enter verification information in a webpage, and the computer will first obtain the IP address before accessing the authentication page. This authentication method is also "using a dynamic IP address to access the Internet" for Routers. When a router accesses the Internet, one of the computers in the LAN performs Web Authentication first, then, other computers can share the Internet without authentication. However, the implementation details of Web Authentication provided by different ISPs vary, so the Web Authentication access method wgr614v9 provided by some ISPs cannot be supported.

The basic Internet access settings are simple as follows:

4.3.1.Log on to the "wgr614v9 Management Interface"Basic settings"After the page, you do not need to make any changes, keep the default settings, and click"Application".

4.3.2.If you can obtain the DNS information from your local ISP (service provider),Domain Name Server (DNS) Address", Select"Use the following Domain Name Server", And then fill in two DNS Server IP addresses, such as 61.144.56.101 and 210.21.4.130. Keep the default settings for other configurations, and then click"Application".

4.3.3.Click"Cancel"To exit and close the management page.

Step 2: wireless network card connection settings for the notebook

5.1.After completing the basic configuration, if you want to connect to the Internet via wireless, you must follow the instructions at the beginning of this article to set"Local Connection"To set the"Wireless Network Connection". Right-click"Wireless Network Connection"Select"View available wireless connections":

Important

If your computer comes with an 802.11b/G wireless network adapter, right-click"Network neighbors"Select"Attribute", Only"Local Connection"Or other connections"Wireless Network Connection", Please contact the after-sales service department of your computer supplier.

5.2.Click"Refresh Network List", The system will list the searched wireless networks on the right, select the desired wireless network, and click"Connection:

Note:If"WindowsUnable to configure this wireless connection ......", You need to contact your laptop manufacturer for the configuration and use of the wireless network card. You can also visit our Chinese website to learn about this issue at http://www.netgear.com.cn /.

Technical Support

This document is used to help you configure your vro for the first time. For more information about other vro functions and their configuration methods, see the help document on the Right of the management interface.
For more technical support information, visit http://www.netgear.com.cn /.
Contact information Technical Support Hotline:800-830-3815Or020-83918600
Technical support Email: tech@netgear.com.cn