The final effect after using PS processing
< small map view big picture > |
| 1, create a new 1000 * 750 pixel file, select the Gradient tool, color settings such as Figure 1, pull out the radial gradient shown in Figure 2 as the background. |
| 2. Create a new group, select the Elliptical Marquee tool, hold down the SHIFT key and pull out the positive circle selections shown in the following illustration, and then add a layer mask to the group, as shown below. |
| 3, create a new layer in the group, select the Gradient tool, color set up with the rainbow gradient, pull out the gradient and then select the Elliptical Marquee tool, in the center of the picture to pull out the overall selection, feather 25 pixels and press the DELETE key to delete the middle part, the effect of the following figure. |
| 4, use the Pen tool to check out the selection shown in the following figure, feather 5 pixels, press CTRL + J to copy the selection of the color block to the new layer, appropriate move the position, and then the bottom of the rainbow gradient layer hidden, the effect of the following figure. |
| 5, create a new layer, with a pen to check out the right edge of the high light selection, feather 20 pixels after filling white, the following figure. |
| 6, create a new layer, with a pen to check out the lower left corner of the high light selection, feather 6 pixels After filling white, you can reduce the opacity of the layer, add layer mask, with a black brush to the two ends of the transition, the following figure. |
| 7, create a new layer, the above method to the lower left corner to add a small high light, the following figure. |
| 8, create a new layer, the above method to the top of a little high light, to the outside of the bubble basically completed. |
| 9, create a new group, with the elliptical marquee tool in the middle of the bubble pull out the positive round selection shown in the following figure, add a layer mask to the group, the following figure. |
| 10, create a new layer in the group, use pen to hook out the edge of the high light area, feather 15 pixels and pull up the linear gradient shown in Figure 12. |
| 11, create a new layer, the above method to the top of the inner bubble to add a little high light, the following figure. |
| 12. Create a new layer, and use the elliptical marquee tool to pull out the oval selection as shown in the image below and fill it with white. After you remove the selection, add the layer mask, and use a black brush to erase the transition from the bottom, as shown below. |
| 13, a new layer, the same method to the bottom to add some light high light, the following figure. |
| 14. Create a new layer, add some small beams to the top, and enhance the details as shown below. Here the inner bubbles are basically finished. |
| 15. Bring up the selection of the outer bubble group, create a new group on top of the layer, and add a layer mask to the group. |
| 16, using the Pen tool to check out the selection shown in the following figure, feather 15 pixels after filling white, as two bubbles in the middle of the high light. |
| 17, the other part of the same method to add some high light, the bubble part of the basic completion, the effect of the following figure. |
| 18. Bring up the selection of the inner bubble group, create a new group above the outer bubble group, and add a layer mask to the group, as shown below. |
| 19. Open the soil material as shown in Figure 21, drag it in, place it properly, and then use the Pen tool to hook up the required parts and add layer masks to the layers, as shown in Figure 22. |
| 20, with a pen to check out the Fringe effect shown in the following figure, feather 2 pixels and then press CTRL + J to copy the selection part of the texture to the new layer, blending mode to "multiply", press CTRL + ALT + G to create a clipping mask, the effect of the following figure. |
| 21, the edge of the soil to increase some dark and high light, the left side of the high light, the right part of the increase in the dark, the following figure. |
| 22, open the grass material, dragged in, properly put the position, with a pen to check out the selection shown in Figure 26, add layer mask to the grassland layer, the effect is shown in Figure 27. |
| 23, the above method to the grassland to add some light and dark parts, such as Figure 28,29. |
| 24, open the green plant material shown in Figure 30, drag in, adjust the size appropriately, the effect is as Figure 31. |
| 25. Create a new layer to add some shadow to green plant, the effect of the following figure. |
| Finally fine-tune the details to complete the final effect. |
