Wireless route connection settings for network cards and routes

Both routes and NICs are the most basic settings for us to log on to the Internet. In terms of wireless networks, what are the differences between these settings? Next we will focus on the main content of wireless route connection settings. First, let's look at the current hardware situation on the market.

This article describes how to operate the wireless network card installed on the computer to connect to the Wireless Broadband Router and build your own wireless LAN. in this article, the wireless router is selected TP-LINK domain? 54M Wireless Broadband Router TL-WR541G, wireless network card is selected TP-LINK domain display/quickplay wireless network card TL-WN510G/550G/610G/megag series products.

1. Wireless route connection settings

◆ Enter the TL-WR541G configuration interface, in the "Wireless Network Basic settings" interface default configuration is as follows:

◆ Meaning of each parameter on the page: SSID: used to identify the service set identifier of a wireless device. the wireless router uses this parameter to identify itself, so that the wireless network card can distinguish different wireless routers to connect. this parameter is determined by the wireless router, not by the wireless network card. Think about it from another angle. For example, there are two wireless routers A and B around the wireless network card, they use ssid a and ssid B to identify themselves. At this time, the identifier of who the wireless network adapter is connected is identified by the SSID.

◆ Here we use the default SSID is the TP-LINK, of course you can change this parameter according to your preferences, to a combination of easy to remember numbers or letters or the two. channel: used to determine the frequency range of the network. The value ranges from 1 to 13. The default value is 6. this parameter only needs to be noted in the application: If your neighbor's house is deployed with a wireless network and the channel used is 6, in order to reduce the Wireless Interference between the two wireless routers, you can change this parameter to 1 or 13.

◆ Wireless route connection Setting Mode: this parameter is used to set the working mode of the wireless router. Two options are available: 54 Mbps (802.11g) and 11 Mbps (802.11b ), we do not need to modify this parameter. The default value is OK. one thing you need to note is: Suppose you purchased our quick exhibition? Ipvm Wireless Broadband Router TL-WR641G, there will be two more options in this parameter, a total of four are 11 Mbps (802.11b), 54 Mbps (802.11g) 108 Mbps (Static) and 108 Mbps (Dynamic), there are two more modes: Static Memory m and Dynamic memory M.

◆ When should I select 108 Mbps (Static) and 108 Mbps (Dynamic? We can determine: if all the wireless network card models connected to WR641G are our fast-moving products? Memory M wireless network card TL-WN610G/650G, this time you can choose WR641G work in Static (Static) memory Mbps mode, in addition to other situations, all choose Dynamic (Dynamic) mbps or 54 Mbps (802.11g) mode.

◆ Enable wireless function: Enable and disable the wireless function of the TL-WR541G. allow SSID broadcast: by default, wireless routers advertise the existence of the SSID to the surrounding space. In this case, you can find the existence of the wireless router. if you remove the hooks in the check box, that is, the Wireless Router does not broadcast the SSID. In this case, the wireless Nic cannot find the existence of the wireless router.

◆ Above this is the TL-WR541G "Wireless Settings" inside the default parameters, when WR541G after power-on, will generate a wireless network around WR541G, the SSID identifier of this network is "TP-LINK", the MIIT is 6, the network is not encrypted. at this time, an unencrypted wireless network exists around WR541G and can be provided to a wireless network card for connection;

Ii. Wireless Nic Configuration

Wireless route connection setup method 1. Setting the wireless network card to connect to the wireless router is complete. Now we will take WN510G as an example to explain how to configure the wireless network card on the computer:

◆ After the installation process is complete, the NIC driver will be properly installed in the computer "Device Manager.

◆ At the same time on the desktop to generate such as the next icon -- "TP-LINK domain display Client Management Program", this program is our management interface card management tool:

◆ At the same time, we will see the following display on the taskbar icon in the lower right corner of the desktop:

◆ Like the two icons above, show that the TL-WN510G has established a wireless network connection with the TL-WR541G, the green icon is "TP-LINK domain expansion" hypervisor display; if your computer's taskbar is not displayed, it is because in the "Network Neighbor" right-click attribute, the "wireless network connection" display attribute is not selected.

◆ The cause is not checked in the red mark! In addition, we also marked a "wireless network connection" property page with a red line above.

◆ The option marked by the red line above is the wireless network card management program that comes with Windows. We do not recommend this option. If this option is checked, it indicates that the Wireless Configuration program that comes with Windows is enabled to manage the network card, this hypervisor conflicts with the "TP-LINK domain Visualization" client hypervisor, and Windows comes with this hypervisor cannot fully play the role of the TP-LINK wireless Nic, so we do not recommend this.

◆ Remarks: The above shows that the TL-WN510G in the normal installation, has established a wireless connection with the TL-WR541G, this is because the operating system in the wireless part of the operating system can automatically run, search for and connect to an existing wireless access point on the wireless router. This process is intelligent without user intervention. By default, the network adapter automatically connects to the wireless router.