axi 1500

................ 　　 Next we will discuss the situations where the following modes are 0, 1 　　 Mode = 1 works in master/slave mode, and eth1 is no arp as the backup Nic [Root @ rhas-13 network-scripts] # ifconfig verify Nic configuration information Bond0 Link encap: Ethernet HWaddr 00: 0E: 7F: 25: D9: 8B Inet addr: 172.31.0.13 Bcast: 172.31.3.255 Mask: 255.255.252.0 Up broadcast running master multicast mtu: 1500 Metric: 1 RX packets: 18495 errors: 0

equals 0 block request return 403#block If!file_req | | Dir_req#block表示阻止请求, returns a 403 error that currently indicates that the request is blocked if the policy file_req is not met or if the policy dir_req is satisfiedUse_backend Server_web If Itnihao_web#当满足itnihao_web的策略时使用server_web的backendUse_backend Server_blog If Itnihao_blog#当满足itnihao_blog的策略时使用server_blog的backend#redirect prefix http://blog.itniaho.cn code 301 if ItnihaoWhen #当访问itnihao. cn, use HTTP 301 to go to http://192.168.16.3

[Root @ 361way network-scripts] # cat ifcfg-enp3s0 DEVICE = enp3s0 TYPE = Ethernet ONBOOT = yes BRIDGE = br0 [Root @ 361way ~] Reboot [Root @ 361way network-scripts] # ifconfig Br0: flags = 4163 Mtu 1500 Inet 192.168.0.102 netmask 255.255.255.0 broadcast 192.168.0.255 Inet6 fe80: 7a24: afff: fe46: ca60 prefixlen 64 scopeid 0x20 Ether 78: 24: af: 46: ca: 60 txqueuelen 0 (Ethernet) RX packe

; SYSDATE, Parallelism => 1, Execution_seconds => 1500, Delay_seconds => 1200 ); END; / BEGIN DBMS_DEFER_SYS.SCHEDULE_PUSH ( Destination => 'dtgdb. com ', Interval => 'sysdate + (1/144 )', Next_date => SYSDATE, Parallelism => 1, Execution_seconds => 1500, Delay_seconds => 1200 ); END; / CONNECT repadmin/repadmin@100.8 BEGIN DBMS_DEFER_SYS.SCHEDULE_PUSH ( Destination => 'orcl16. com ', Interval => 'sysda

information-S Display summary information (similar to netstat-i)Add to configure the IPV6 address for the specified NICdel Deletes the IPV6 address of the specified network cardmtunetmaskTunel establishing a tunneldstaddr set a remote address to establish point-to-point communication-broadcast-pointtopointMulticast Setting the multicast flag for the network cardaddress sets IPV4 addresses for network cardstxqueuelen4. Usage Examples:Example 1: Displaying network device information (active state

If you have read VMware's network configuration in detail (a) , now continue to understand;First, use the CMD program under Windows System, ping one by using the ping commandThe network host name or IP address that can be connected:Then ping the same host name on the FEDORA15 system:Should be related to the type of network settings, my network card is the way to set host-only;So in order for the FEDORA15 to be able to ping the host address, let's set the next newThe network card, but does not

; backcolor= "Transparent" bordercolor= "Red" borderwidth= "0px" descriptiontext= "currently in use:" Gotobuttonvalue= "Go" Cssclass= "Navi" isgotoselectvisible= "false" isgototextboxvisible= "false" leftpagesize= "0" rightpagesize= "0" currentnumberbgcolor= "White"/> backcolor= "Transparent" bordercolor= "Red" borderwidth= "0px" descriptiontext= "" gotobuttonvalue= "to" CssClass= "Navi" recordcount= "1500" isgotoselectvisible= "false" isgototex

Failure phenomenon: 1, on the Vnxe, can not use 192.168.2.2 this IP address to create a shared folder server or iSCSI server; 2, the use of 192.168.2.2 this IP address to create a server failed, and reported "IP address has been used (error code: 0X600089C)" error message. Solution: 192.168.2.2 This IP address is occupied by the data mover of the Vnxe two storage processor (SP). You can log in to the Vnxe command-line interface by putty using the service account. Then follow these steps: Se

Recently, because in the study remoting, pure just understand, discover remoting is really good thing. We usually have three ways to use remoting, one of which is First: Publishing a public objectThe exposed object is created locallySecond: Remote creation of a public object (SAO)Object created in client requestThird: Remote creation of a private object (CAO)object is created on the host, and the client references the object on the server I don't really understand the essence of these three kind

Tags: Linux routing configuration Miscellaneous basics11.211.2.1 ifcfg View Linux Routing entries[[emailprotected] ~]# route -nKernel IP routing tableDestination Gateway Genmask Flags Metric Ref Use Iface10.201.106.0 0.0.0.0 255.255.255.0 U 0 0 0 eth00.0.0.0 10.201.106.2 0.0.0.0 UG 0 0 0 eth0View system Activity Status Network interface information[[emailprotected] ~]# ifconfigens33: flags=4163Show all active a

Network//Tcpserver.java by Fpont 3/2000 //Usage:java tcpserver //default port is 1500. //connection to is closed by client. //This server handles only 1 connection. import java.net.*; import java.io.*; public class TCPServer { public static void Main (String args[]) { int port; ServerSocket Server_socket; BufferedReader input; try { port = integer.parseint (Args[0]); } catch (Exception e) { System.out.println ("port =

Up interface Bond0 OKBringing Up interface eth0 OKBringing Upnbsp;interface eth1 OK................Below we discuss the following mode for 0, 1 o'clock, respectively.mode=1 operation in the main standby mode, then eth1 as the Backup network card is no ARP[email protected] network-scripts]# ifconfig Verify the configuration information of the NICBond0 Link encap:ethernet HWaddr 00:0e:7f:25:d9:8binet addr:172.31.0.13 bcast:172.31.3.255 mask:255.255.252.0Up broadcast RUNNING MASTER multicast mtu:

network card device: # VIM Ifcfg-eth0 device= "eth0" bootproto= "static" Hwaddr= "08:00:27:6a:9d:57" nm_controlled= " No" onboot= "Yes" Bridge= "Xenbr0" type= "Ethernet" userctl= "No" 3. Configuring bridging mode requires the NetworkManager service to be turned off: All two nodes need to operate #chkconfig NetworkManager off #service Restart the Network service after NetworkManager stop configuration: #service Network Restart 4). Login terminal to view bridge status: #