cisco fastethernet

(config) #interface fastethernet 0/3 into Fast Ethernet interface 0/3Switch (config-if) #switchport Access VLAN 2 Switch interface Access VLAN 2 groupSwitch (config) #interface fastethernet 0/4Switch (config-if) #switchport Access VLAN 2Switch (config) #interface fastethernet 0/5Switch (config-if) #switchport Access VLAN 3Switch (config) #interface

features: readable, writable, easy to lose-rom: (System important boot file) read-only memory features: readable, non-writable, not easy to lose-flash: Flash (save operating system) features: readable, writable, not easy to lose-nvram: Non-volatile random access memory storage configuration Delete This configuration is to restore the factory settings(2) boot process for Cisco routers3. Cisco Configuration

(Config-router) #exitIf this is all configured, then use the ping command to test it!Here is a start-up-configuring HSRP Hot Spares:Configure on the active three-layer switch:Switch (config) #interface vlan 1Switch (config-if) #standby 1 IP 192.168.1.254Switch (config-if) #standby 1 priority 200Switch (config-if) #standby 1 track fastethernet 0/2Switch (config-if) #standby 1 preemptConfigure on the backup layer three switch:Switch (config) #interface

Cisco 2960 Switch Configuration1. Cisco Working mode classification and function#用户模式仅答应基本的监测命令, the configuration of the router cannot be changed in this mode.Switch> #用户模式#允许用户执行所有的测试, view, save and other commands, this mode can not be modified router configuration, generally this mode is recommended to set password protection.Switch>enable #进入特权模式switch##允许用户配置路由器.switch#Configure terminal #进入全局模式Sw

Cisco configuration instance _ Cisco dual-Egress NAT configuration objective: to simulate the routing function based on the original address policy when a dual-Egress link is available, and access to the external network from different original addresses is realized, in most cases, the vro uses NAT to translate the Intranet address on the external port, so this experiment also uses dual NAT to translate the

to guess. It can be seen that network security is similar to the barrel principle, and it is always broken through the weakest link. (Figure 3) (2). Cisco attack test Since the vro is controlled, we cannot determine whether the vro is the company and its relationship with web servers. By entering the show ip interface brif command on the vro, it is found that almost all the serdrop (Serial Port) interfaces of the vro are activated, while the Fast Et

(config) #no monitor session 1Switch (config) #endSwitch#wrSwitch#show MonitorNo SPAN configuration is present in the system.3. Other(1) Port image filtering, port mirroring can do filter.Monitor session session_number Filter VLAN Vlan-id [, |-]* * Specifies which VLANs belong to the traffic that the source port is entering, and can be emitted from the destination port.(2) Delete imageNo monitor session {Session_number | all | local | remote}**SESSION_NUMBER Specifies the session number, all is

port status is enable!!# Module 1 empty!# Module 2: 2-port 1000 BaseX Supervisor!# Module 3: 48-port 10/100 BaseTX EthernetSet vlan 2 3/4Set port disable 3/5Set port speed 3/1-2 100Set port duduplex 3/1-2 fullSet trunk 3/1 nonegotiate isl 1-1005Set trunk 3/2 nonegotiate isl 1-1005! -- If IEEE 802.1q is configured,! -- You will see the following output instead:Set trunk 3/1 nonegotiate dot1q 1-1005Set trunk 3/2 nonegotiate dot1q 1-1005Set port channel 3/1-2 mode on!# Module 4: 24-port 100 BaseFX

An instance of VLAN configuration for Cisco L3 switches and L2 SwitchesCisco VLAN implementation is usually port-centric. The port connected to the node determines the VLAN in which it resides. There are two ways to allocate a port to a VLAN: Static and Dynamic. The process of creating a static VLAN is to forcibly allocate the port to a VLAN. That is, we first create a VLAN on The VTP (VLAN Trunking Protocol) server, and then assign each port to the c

From today onwards, let's show a few of the basic features of Cisco UC, one of the first basic features: Cisco IP Phone.The word Cisco CUCM is bull x!Knowing that the CUCM is a ippbx in a cow's lecture, it provides the phone function of the IP phone to replace the traditional analog phone.In fact, know this is a broken cow, but also in the study of Microsoft's UC

With the advent of the Internet era, more and more work and information technology-related, in the requirements of the times, each person's development and employment needs to have the knowledge and quality of the Internet, then in this do not test the certificate of the age, Cisco gold content such a high certificate in the end there is no use? The leading-edge education small compilation uses the data to explain the question.Because our large depart

Cisco single-ARM routing configuration One-arm routing, which is to set up multiple logical subinterfaces on the router, one VLAN for each sub-interface. The data on each sub-interface is passed on the physical link to be labeled encapsulated. Cisco devices support ISL and 802.1q (dot1q) protocols. Huawei only supports 802.1q. The difference between dot1q and ISL: dot1q is a generic VLAN protocol model for

Branch switches.The Cisco switch can support any media as a trunk line. To achieve relay, you can use its unique isl tag. Isl (inter-switch link) is a protocol for transmitting vlan information and vlan data streams between switches, between switches and routers, and between switches and servers, by configuring isl encapsulation on the port directly connected to the vswitch, you can allocate and configure VLANs across the entire network.The core swit

domain COM settings vtp admin domain name com PAR2 (VLAN) #vtp client to set the switch to clients mode Par3#vlan database into VLAN configuration mode PAR3 (VLAN) #vtp domain COM settings vtp admin domain name com PAR3 (VLAN) #vtp client to set the switch to clients mode Note: Setting the switch to server mode is to allow the creation, modification, deletion of VLANs and other configuration parameters for the entire VTP domain on this switch, and to synchronize the latest VLAN information

. Cisco router in the configuration of ports, or to understand the next few port names and purposes more meaningful, s port is the meaning of serial interface, also known as high-speed asynchronous serial port, is mainly connected to the WAN v.35 cable, commonly said routers and routers when used in connection. F port is a fastethernet interface, called Fast Ethernet port, mainly connected to Ethernet (LAN

This tutorial describes how to start and configure Cisco Catalyst 1900 series switches.1. Tutorial PurposeThrough this experiment, you can master the following skills:Familiar with switch startup interface;Configure the vswitch;Understand the port number of the vswitch.2. device requirementsThis experiment requires the following devices:One Cisco Catalyst 1900 Series Switch with unlimited models and Enterpr

Half a year five acquisitions Cisco intensive integration for self-redemptionWu MicroCisco, a "takeover guru", recently announced a new deal.The acquisition was Cloudlock, a cloud security company, with a total transaction price of $293 million. This is the fifth takeover deal that Cisco has launched this year.As the world's largest network equipment manufacturer, Cisco