============ Problem Description ============Because learning needs to look at the old Luo's video about the data stored in the SD card to write the part of the file to almost completely comply with the knock code results on the pad test and expected to have a difference originally should be stored in the SD card file
An error occurred while mounting the SD card-Linux general technology-Linux technology and application information. For details, refer to the following. The SD card is inserted and the following information is detected:
Mmc0: new SD
How do I add files to the SD card on the android simulator mobile phone?
Add a file directly to the SD card of the simulator in ddms. If an error occurs, such as: failed to push xxxxx.txt on emulator-: Read-Only file system, the error
Why mobile phone SD card is unavailableFirst, you need to find out whether the problem is the SD card or the mobile phone. If the problem is the SD card, change the SD
The first step, remember that we first put the cell phone SD card in the card reader and then insert the reader into the computer to display a removable disk.
Step two, okay. Now we turn on the computer "start"-"Run"-enter "CMD".
The third step, and then in the open cmd we enter "chkdsk/f #:" (# is your
= (8/CLK) *arg. 5. NBSP;NBSP;NBSP;NBSP;NBSP;2GB the SD card (standard card) and more than 2GB SD card (high-capacity card) in the form of address access, this is particularly important to note, otherwise there will be no read and
the SD card supports offset read and write operation), and the Address field Fu Yan value 0x10 in the high capacity card read or write command token The 16th block reads and writes, and the bulk card only supports block read and write operations, the block size is fixed to 512 bytes, and the byte operation will
the SD card supports offset read and write operation), and the Address field Fu Yan value 0x10 in the high capacity card read or write command token The 16th block reads and writes, and the bulk card only supports block read and write operations, the block size is fixed to 512 bytes, and the byte operation will
interface to read and write the files inside the SD card. The average read and write speed of a 10MB size file is tested with 2KB size as read-write unit.
uint8_t testbuffer[2048];
int main ()
{
uint32_t i;
FATFS FS;
FIL file;
Fresult Res;
uint32_t Timecount;
uint32_t Bytewrite, Byteread;
/* Board pin, clock, debug console init */
/*attach MHz clock to FLEXCOMM0 (Debug console) */
CLOCK_ATTACHCLK (Board_d
choice, and you should see most of the files you want to salvage.
Tips for repairing SD cards
Because the plastic shell is very thin, the standard size SD card is easy to damage, if you put the case in your pockets or without protection, the cards will easily break down.
Sometimes the little write-protection switch will fall off, allowing the
note: in fact, do not need Cygwin directly download a SYSLINUX and then in the syslinux-3.60/win32/directory to execute the command: syslinux.exe-a g: it can be, g: Is the SD card)
Note that the above command should not use the-s option. It will install SYSLINUX in safe mode, so it may take a long time to boot the system, and it is unnecessary for SD to install
SD Card write protection How to remove the solution:
Step 1, about the SD card write protection How to remove the problem, you can use the disk repair program to repair the SD card. Open My Computer, locate the
:# make Arch=arm Cross_compile=arm-linux-gnueabi HF -Uimage here to note is that the marked place cannot be less than the compilation error When this is finish ' s you'll have uimage ready and you can build the kernel modules:# Make Arch=arm cross_compile=arm-linux-gnueabi-install_mod_path=out modules# Make Arch=arm cross_compile=arm-linux-gnueabi-install_mod_path=out Modules_installFormat and setup the Sd-
, help, the most critical is the last sentence, where auto represents the first partition mounted SD card, followed by the Vold monitoring path, when inserting SD,/DEVICES/PLATFORM/S3C-SDHCI.0/MMC_HOST/MMC0 There will be more than one folder under the path, please confirm the corresponding path of your hardware platform.
Finally, there are a few things to focus
capacity problem. I understood it! Note that the function name here is the number of read sectors, and the actually returned value is the capacity of our card. Pay attention to it here.
1. First, check the code
U32 SD_GetSectorCount (void) {u8 csd [16]; u32 Capacity_KB, Capacity_MB; u8 n; b2csize; // obtain CSD information. If an error occurs during this period, returns 0 if (SD_GetCSD (csd )! = 0) return
(1) Verify that the Linux system on the board recognizes the SD card via the #fdisk-l commandMP805M board is displayed after inserting the SD cardSD30 slot is without WPMmc1:new High speed SD card at address 5bc0MMCBLK0:MMC1:5BC0 sd02g 1.83 GiBMmcblk0:p1[/]# fdisk-lDisk/dev/
Believe that a lot of friends have encountered such a problem, that is, through the card reader will be inserted into the computer SD card Computer "whether to format" prompts, and the SD card inserted into the camera, and the "SD
driver bus driver and client driver are provided by Microsoft, but not by Microsoft itself. It looks like it was developed by bsquare. The code of the bus layer is located in C:/wince500/public/common/oak/Drivers/sdcard/sdbusdriver. (C:/wince500 is the directory where you install wince ). The client code is located in C:/wince500/public/common/oak/Drivers/sdcard/sdclientdrivers. Microsoft has two client drivers (Bluetooth and sdmemory ). The following describes the main functions of each layer.
The content source of this page is from Internet, which doesn't represent Alibaba Cloud's opinion;
products and services mentioned on that page don't have any relationship with Alibaba Cloud. If the
content of the page makes you feel confusing, please write us an email, we will handle the problem
within 5 days after receiving your email.
If you find any instances of plagiarism from the community, please send an email to:
info-contact@alibabacloud.com
and provide relevant evidence. A staff member will contact you within 5 working days.