m17 r3

The topology is Darip CCNP experiment Lab17, described as follows: R1 (S1/1)--r2 (s1/0), Cost=10;r1 (S1/2)-framerelay-r4 (S1/2), cost=2 R2 (S1/1)--R3 (s1/0), COST=2,R2 (f0/0)--r4 (f0/0), cost=2 R3 (S1/1)--r4 (s1/0), cost=5 R1 f0/0 Port Connection Network 192.168.1.0/24,cost=1 R1#show Run Interface fastethernet0/0IP address 192.168.1.1 255.255.255.0 ! Interface SERIAL1/1Description DCE,OSPF area 0,co

Experiment topology of ipv6 Network Protocol Configuration:Tutorial objective: (1) configuring rip Protocol in ipv6 (2) configuring ospf protocol in ipv6 (3) configuring ospf protocol in ipv6 (4) let the two ipv6 networks pass through ipv4 network communication (Tunnel) www.2cto.com basic information configuration IP Address Allocation: r1: f0/0: 2000: 1/16s1/0: 2001: 1/16r2: s1/0: 2001: 2/16s1/1: 2002: 1/16r3: s1/0: 2002: 2/16f0/0: 2003 :: 1/16 ipv6 Address Configuration: r1 (config) # in f0/0r

Implementation of MD5 Algorithm in JS　 /*************************************** ******************** Md5.js** A JavaScript Implementation of the RSA Data Security, Inc. MD5* Message-Digest algorithm.** Copyright (c) Paul johnaston 1999. distributed under the lgpl.**************************************** *******************/ /* To convert strings to a list of ASCII values */VaR sascii = "! /"# $ % '() * +,-./0123456789:; VaR sascii = sascii + "[//] ^ _ 'abcdefghijklmnopqrstuvwxyz {| }~ "; /* C

btg2 = G btr2 = r)Return true;ElseReturn false;} // Corresponding AssemblyAssembly instructions. Text: 00013668 cdzqsplash_dlg _ getcoloryes; Code xref: cdzqsplash_dlg _ setrgnsplash + 368 P. Text: 00013668; cdzqsplash_dlg _ setrgnsplash + 3ccp. Text: 00013668; Data xref :.... Text: 00013668. Text: 00013668 arg_0 = 0 // parameter 1. Text: 00013668 arg_4 = 4 // parameter 2. Text: 00013668 arg_8 = 8 // parameter 3. Text: 00013668 arg_c = 0xc // parameter 4. Text: 00013668 arg_10 = 0x10 // param

is as follows: [CPP] view plain copy addr0,r1,r2 nbsp;@r0=r1+r2 Addr0,r1, #256 @R0=R1+256 addr0,r2,r3,lsl#1@r0 =R2+ (r3 2.2 with carry addition instruction ADC adc{conditions}{s} purpose register, operand 1 NBSP;ADC instruction is used to add two operands, plus the value of the C condition flag in CPSR, and store the results in the destination register. It uses a carry flag bit so that you can do

A dead loop was encountered while porting a Windows program to Linux, and finally a statement similar to this was located for (i = 0; i Don't ask me who wrote it, why do you write it so ( tear eyes !) ).According to the common sense of c, i = i++ should be equivalent to i++, it is true on Windows, but Linux is not, this should be caused by compiler differences.---------------------------------------Split-line no.0------------------------------------------------------------- --------------------

(6) Label: MUL2 function: Double-byte binary unsigned number squared(a+b) ^2=a*a+b*b+2*a*b(90+9) ^2=90*90+9*9+2*90*9=8100+1620+81=98019999--------891+ 891--------98019 9Entrance Condition: Square number in R2, R3Export information: results in R2, R3, R4, R5.Impact resources: PSW, A, B, R2~R5 stack requirements: 2 bytesMul2:mov a,r3; calculate R3 SquaredMOV B,aMUL

1. explore the election process 1.1 experiment topology 1.2 experiment requirements (1) configure the basic IP address based on the topology (2) Capture packets on the shared link and pay attention to the Hello message during OSPF neighbor relationship establishment (3) debug the OSPF joining relationship on R1, R2, R3, and R4 (4) sequentially declare the direct connection network of R1, R2, R3, and R4 to t

Frame-relay:: Configure Frame-relay SWITCH so that the Frame-relay PVC between R2,R3,R3 is Full-mesh. However, only the PVC shown in the figure can be used.R2,R3,R4 Physical Interface Connection Framme-relay SWITCHBetween R4 and R5, use a PPP link. Please eliminate redundant 32-bit host routingR1,R2,R3 's Ethernet port

floating-point operations. So allVFP commands are actually some coprocessor commands. For example, fadds is actually a CDP command, and FLDS is a LDC command. Theoretically, As long as arm1136jf-S CPU should be able to support VFP. 3. compiler support for VFPA floating point number operation is finally translated into a VFP command, or translated into FPA, or softfloat is determined by the compiler. Instance:[SJL @ sjl vfp] $ cat F. CInt main (){Float F1 = 1.2, f2 = 1.3;F1 = F2 * F1;}[SJL @ sjl

routerID [R1] ospf1 rof1-id 2.2.2.2 area 0.0.0.0 network 10.1.1.1 0.0.0.0 network 10.1.12.1 0.0.0.0 [R2] ospf1 rof1-id 2.2.2.2 area 0.0.0.0 network 255.0.0.0.0 network 10.2.2 1.0.0.0.0: r1 and R2 cannot establish OSPF neighbor relationship. Analysis: After R1 sends the hello packet, R2 receives the hello packet from R1 and finds that the routerID is consistent with its own router ID, and the neighbor cannot be established. 3) Scenario 2: R1, R2, and R3