pcie development board

Beaglebone Black Development Board installation driverBeaglebone Black Development Board installation driver, before using Beaglebone Black Development Board to do anything before the first need to install the driver. The followin

The previous chapters mainly describe the installation and construction of the native Linux Android development environment and the porting of the Android system. This chapter focuses on how to install Android on the Development Board . Development boards are the main hardware devices for developing and learning embed

Environment Monitoring System Based on zigbee and tiny4412 Development Board, zigbeetiny4412 1. Build the Development Board Environment 　　1. layout of tiny4412 linux Reference blog: http://www.cnblogs.com/luoxiang/p/4186391.html 2. boa Server Construction　　 Download boa Source package: http://www.boa.org/boa-0.94.14rc2

, Amy electronics guessed that Altera cut down the low-end fpga I/O diode clamp protection circuit to reduce costs. Recommended plugging Sequence Cabling Sequence 1. Power off the FPGA Development Board; 2. Connect the JTAG cable of the JTAG simulator to the JTAG interface of the FPGA Development Board; 3. Ins

file: 4.1 create/etc/inittab. The content is as follows: #/etc/inittab: sysinit: /etc/init. d/RCS: askfirst:-/bin/sh: ctrlal Tdel:/sbin/reboot: shutdown:/bin/umount-a-r4.2 create/etc/init. d/RCs, the content is as follows: (After creation, change its attributes so that it can execute sudochmod + x/etc/init. d/RCs )#! /Bin/sh (this script is mainly used to automatically generate device files) # ifconfigeth0192.168.1.17mount-amkdir/dev/ptsmount-tdevptsdevpts/dev/ptsecho/sbin/mdev>/proc/sys/kernel

Altera officially has a de2 Development Board, which has rich resources and complete peripherals. It uses ten-layer circuit board design, and the price is naturally high. I made a piece based on the principle diagram, called diy_de2 Development Board. The

Recently, two jz4750 APUs development boards are required for trial. This is also the first contact. I encountered a lot of problems in the middle and finally spent a lot of time doing a good job. Here I will summarize all the process records (for the time being, I cannot upload a picture, and I will try it again if I have a chance ). This diary is divided into the following points: 1. hardware connectivity 2. Linux environment construction and kerne

1. OverviewEmbedded system consists of hardware environment, embedded operating system and application, hardware environment is the hardware platform of operating system and application, it has different requirements depending on the application. The diversity of hardware platform is the main feature of embedded system, how to make the embedded operating system run effectively on different hardware platform is the key problem in the development of emb

When using GDB on the Development Board debugging, sometimes need to look at the source code, but the source code is too large, the development Board capacity is limited to pass through the SCP every time the development Board, or

Update Development Board firmware The IDE contains the released board and sub-dedicated firmware. Follow these steps to update your board with IDE:(1) disconnect all power supplies (USB and 5 V power supplies ). Make sure no sketch is running on the board(2) Remove the SD c

The Development Board launched earlier does not have a network port. Therefore, many network-based functions of the. NET micro framework cannot be studied. In the IOT era, network functions are king. In addition to the Ethernet module, the New Development Board also adds the USB Host module and other related interfaces

AC6102 Development Board USB3.0 test and use instructionsOverviewThe AC6102 incorporates a cypress-launched high-performance USB3.0 transmission chip cyusb3014,cypress called EZ-USBFX3. The chip features strong, powerful, simple interface and is ideal for use in a variety of applications where high-speed data transmission is required, following an introduction to the chip from the EZ-USBFX3 data sheet:Cypre

Building nfs server fedora13 in the development board environment of s3c6410 and building nfs server in the development board environment of is a revolutionary tool for the development board! With nfs, you don't need to keep your

Iconv_open ("UTF-8", "gb2312") on ARM development board The application code is as follows: Static int code_convert (char * from_charset, char * to_charset, char * inbuf, size_t inlen, char * outbuf, size_t outlen) { Iconv_t CD; Char ** pin = inbuf; Char ** pout = outbuf; Cd = iconv_open (to_charset, from_charset );If (Cd =-1){Perror ("iconv_open :");Return-1;} Memset (outbuf, 0, outlen );If (iconv (Cd,

MiS603 Development Team Date: 20150911 Company: Nanjing mi Lian Electronic Technology Co., Ltd. Forum: www.osrc.cn Website: www.milinker.com Shop: http://osrc.taobao.com Eat blog: http://blog.chinaaet.com/whilebreak Blog Park: http://www.cnblogs.com/milinker/ MiS603 Development Board Chapter 11th CY7C68013A Slave FIFO return transmissionCY7C68013A provides a powe

flash device number, you can use the command "NAND device" to view the specific Flash device information on the Development Board. Offset refers to the starting offset address of the kernel file in Flash. It automatically reads the end of the kernel image (processed with mkimage), so no read size is given. Example:Nboot 80700000 0 200000Tftpboot [LOADADDR] [[Host_ip:]filename] uses the TFTP protocol to boo